Re: [CAD_CAM_EDM_DRO] Z axis conversion
Posted by
diazden
on 2000-11-27 15:41:35 UTC
And I wonder if it will need a counter weight , my mill mod is similar to
Jon ,TANKS, JON and I intend to motorize the knee but putting ball screws
on the Knee I think that will create a problem
regards
mariano
Joe Vicars wrote:
Jon ,TANKS, JON and I intend to motorize the knee but putting ball screws
on the Knee I think that will create a problem
regards
mariano
Joe Vicars wrote:
> In my opinion, gentlemen (and ladies) the "knee" will not make a
> good "Z". The quill bolt ons I agree aren't great, but you get to
> messing with that knee and you'll regret it. There is a bevel reduction
> gear in there (that's about 2:1) so there is some backlash. Even though
> I think Smoke is right about not needing a anti-backlash nut. So, you
> have to get all that out of there and fit a motor up inside the knee
> somehow? I don't think so.
> Not to mention you have to move 3 big castings, the knee, the table,
> and the saddle. All together 500 pounds at least! Crank on that knee
> up and down several times a day, it's a good workout. You're going to
> put an awful load on any reasonable sized motor.
> The Knee Way? No way!!!!
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager
Discussion Thread
Joe Vicars
2000-02-16 07:58:39 UTC
Z axis conversion
Charles Hopkins
2000-02-16 10:43:27 UTC
RE: Z axis conversion
Jon Elson
2000-02-16 21:05:59 UTC
Re: Z axis conversion
F. de Beer
2000-02-17 11:13:00 UTC
Re: Z axis conversion
SMITH, THOMAS B. (JSC-DX)
2000-02-17 12:16:40 UTC
RE: Z axis conversion
Drew Rogge
2000-02-17 13:05:18 UTC
Re: RE: Z axis conversion
stratton@m...
2000-02-17 16:16:20 UTC
Re: Z axis conversion
Jon Elson
2000-02-17 21:42:10 UTC
Re: RE: Z axis conversion
Jon Elson
2000-02-17 21:59:57 UTC
Re: Z axis conversion
SMITH, THOMAS B. (JSC-DX)
2000-02-18 07:52:51 UTC
RE:Z axis conversion
Jon Elson
2000-11-27 12:03:54 UTC
Re: [CAD_CAM_EDM_DRO] Z axis conversion
Smoke
2000-11-27 12:32:49 UTC
Re: [CAD_CAM_EDM_DRO] Z axis conversion
Wally K
2000-11-27 12:43:23 UTC
Re: Z axis conversion
Wally K
2000-11-27 12:53:04 UTC
Re: Z axis conversion
Smoke
2000-11-27 13:16:50 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
James Owens
2000-11-27 13:17:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
Wally K
2000-11-27 13:25:48 UTC
Re: Z axis conversion
Wally K
2000-11-27 13:31:02 UTC
Re: Z axis conversion
Joe Vicars
2000-11-27 13:44:59 UTC
Z axis conversion
Wally K
2000-11-27 13:58:05 UTC
Re: Z axis conversion
Joe Vicars
2000-11-27 14:01:39 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
dave engvall
2000-11-27 14:26:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
Andy Anderson
2000-11-27 14:40:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
Wally K
2000-11-27 14:46:29 UTC
Re: Z axis conversion
Smoke
2000-11-27 15:08:08 UTC
Re: [CAD_CAM_EDM_DRO] Z axis conversion
Smoke
2000-11-27 15:10:15 UTC
Re: [CAD_CAM_EDM_DRO] Z axis conversion
Smoke
2000-11-27 15:14:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
Wally K
2000-11-27 15:22:25 UTC
Re: Z axis conversion
diazden
2000-11-27 15:41:35 UTC
Re: [CAD_CAM_EDM_DRO] Z axis conversion
Smoke
2000-11-27 15:55:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
Jon Elson
2000-11-27 16:16:26 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
Jon Elson
2000-11-27 16:20:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
Jon Elson
2000-11-27 16:23:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
Jon Elson
2000-11-27 16:26:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
Wally K
2000-11-27 16:47:38 UTC
Re: Z axis conversion
dave engvall
2000-11-27 21:12:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
dave engvall
2000-11-27 21:25:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
Jon Elson
2000-11-27 23:03:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
Smoke
2000-11-27 23:58:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
Smoke
2000-11-28 00:06:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
diazden
2000-11-28 05:51:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion