Re: Z axis conversion
Posted by
Wally K
on 2000-11-27 13:25:48 UTC
I think i read somewere that the z axis will fall down if you install
a ball screw and remove power from the drive motor. Have to be a
little carefull.
I peeked in my bridgeport knee by laying on the ground and using
light to see up inside it. Not sure how you would change this screw.
And like you said before a preloaded ballnut may not be needed.
Wally K.
Smoke wrote:
a ball screw and remove power from the drive motor. Have to be a
little carefull.
I peeked in my bridgeport knee by laying on the ground and using
light to see up inside it. Not sure how you would change this screw.
And like you said before a preloaded ballnut may not be needed.
Wally K.
Smoke wrote:
> Unfortunately, i found it long before I found this egroups site.If i ryun
> across it again, I'd be happy to post it. I want to power the kneeon my
> "imitation" bridgeport and am wondering how to install the ballscrew in the
> knee once I get them.Wally K. wrote;
>
> Smoke
> >Smokie, If you know were that site was that used the knee for the Zis
> >axis it would be very helpfull if you posted it. I think that it
> >worth exploring.
> >
Discussion Thread
Joe Vicars
2000-02-16 07:58:39 UTC
Z axis conversion
Charles Hopkins
2000-02-16 10:43:27 UTC
RE: Z axis conversion
Jon Elson
2000-02-16 21:05:59 UTC
Re: Z axis conversion
F. de Beer
2000-02-17 11:13:00 UTC
Re: Z axis conversion
SMITH, THOMAS B. (JSC-DX)
2000-02-17 12:16:40 UTC
RE: Z axis conversion
Drew Rogge
2000-02-17 13:05:18 UTC
Re: RE: Z axis conversion
stratton@m...
2000-02-17 16:16:20 UTC
Re: Z axis conversion
Jon Elson
2000-02-17 21:42:10 UTC
Re: RE: Z axis conversion
Jon Elson
2000-02-17 21:59:57 UTC
Re: Z axis conversion
SMITH, THOMAS B. (JSC-DX)
2000-02-18 07:52:51 UTC
RE:Z axis conversion
Jon Elson
2000-11-27 12:03:54 UTC
Re: [CAD_CAM_EDM_DRO] Z axis conversion
Smoke
2000-11-27 12:32:49 UTC
Re: [CAD_CAM_EDM_DRO] Z axis conversion
Wally K
2000-11-27 12:43:23 UTC
Re: Z axis conversion
Wally K
2000-11-27 12:53:04 UTC
Re: Z axis conversion
Smoke
2000-11-27 13:16:50 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
James Owens
2000-11-27 13:17:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
Wally K
2000-11-27 13:25:48 UTC
Re: Z axis conversion
Wally K
2000-11-27 13:31:02 UTC
Re: Z axis conversion
Joe Vicars
2000-11-27 13:44:59 UTC
Z axis conversion
Wally K
2000-11-27 13:58:05 UTC
Re: Z axis conversion
Joe Vicars
2000-11-27 14:01:39 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
dave engvall
2000-11-27 14:26:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
Andy Anderson
2000-11-27 14:40:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
Wally K
2000-11-27 14:46:29 UTC
Re: Z axis conversion
Smoke
2000-11-27 15:08:08 UTC
Re: [CAD_CAM_EDM_DRO] Z axis conversion
Smoke
2000-11-27 15:10:15 UTC
Re: [CAD_CAM_EDM_DRO] Z axis conversion
Smoke
2000-11-27 15:14:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
Wally K
2000-11-27 15:22:25 UTC
Re: Z axis conversion
diazden
2000-11-27 15:41:35 UTC
Re: [CAD_CAM_EDM_DRO] Z axis conversion
Smoke
2000-11-27 15:55:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
Jon Elson
2000-11-27 16:16:26 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
Jon Elson
2000-11-27 16:20:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
Jon Elson
2000-11-27 16:23:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
Jon Elson
2000-11-27 16:26:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
Wally K
2000-11-27 16:47:38 UTC
Re: Z axis conversion
dave engvall
2000-11-27 21:12:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
dave engvall
2000-11-27 21:25:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
Jon Elson
2000-11-27 23:03:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
Smoke
2000-11-27 23:58:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
Smoke
2000-11-28 00:06:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion
diazden
2000-11-28 05:51:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: Z axis conversion