CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re:Digitizing

Posted by Smoke
on 2001-01-07 22:35:29 UTC
Sounds good to me. Since your going to be using a dial indicator, the point
of contact will lie somewhere on the surface of a sphere or other geometric
surface depending the indicator point you use. I suppose your going to put
in some sort of routine for calculating the actual location of the contact
point?

Incidently....I was just looking at an ad in a flyer from MSC. they have a
digital measuring unit that could probably be adapted pretty easily to
provide that Z signal you require.

Smoke

>This is the step in which I will differ. Because I'm going to use a spring
loaded digital indicator, I can rapid to position, don't have to worry about
crashing the machine or the probe, and then I will:
>
>5) Send signal to PC to read Indicator
>6) Interrogate Indicator for current value in Z.
>7) Signal Control to continue after signal is read.
>8) Proceed to next position by rapid up to clearance plane, rapid to next
point, rapid down to measurement plane.
>
>
>Best Regards, Fred Smith- IMService
>Listserve Special discounts and offers are at:
http://209.69.202.197/cadcamedmdro.html
>
>imserv@... Voice:248-486-3600 or 800-386-1670 Fax: 248-486-3698
>
>
>Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
>Addresses:
>Post message: CAD_CAM_EDM_DRO@egroups.com
>Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
>List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
>Moderator: jmelson@... [Moderator]
>URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
>FAQ: http://www.ktmarketing.com/faq.html
>bill,
>List Manager
>
>
>

Discussion Thread

Jon Anderson 2001-01-07 16:09:10 UTC Re: [CAD_CAM_EDM_DRO] Digitizing ballendo@y... 2001-01-07 16:14:36 UTC re:Digitizing Fred Smith 2001-01-07 18:14:46 UTC Re:Digitizing Jon Elson 2001-01-07 20:21:46 UTC Re: [CAD_CAM_EDM_DRO] Digitizing Smoke 2001-01-07 22:35:29 UTC Re: [CAD_CAM_EDM_DRO] Re:Digitizing Smoke 2001-01-07 22:49:47 UTC Re: [CAD_CAM_EDM_DRO] re:Digitizing Jon Anderson 2001-01-08 07:47:47 UTC Re: [CAD_CAM_EDM_DRO] Digitizing Marcus & Eva 2001-01-08 08:28:51 UTC Re: [CAD_CAM_EDM_DRO] re:Digitizing Bill Phillips 2001-01-08 13:55:04 UTC Re: [CAD_CAM_EDM_DRO] Digitizing Greg Nuspel 2001-01-08 14:02:31 UTC Re: [CAD_CAM_EDM_DRO] Digitizing diazden 2001-01-08 15:15:53 UTC Re: [CAD_CAM_EDM_DRO] Digitizing ballendo@y... 2001-01-08 17:05:13 UTC Re: re:Digitizing dave engvall 2001-01-08 17:20:30 UTC Re: [CAD_CAM_EDM_DRO] Re: re:Digitizing Jon Elson 2001-01-08 23:45:05 UTC Re: [CAD_CAM_EDM_DRO] Re: re:Digitizing nelap2002 2004-01-04 21:29:52 UTC Digitizing Graham Stabler 2004-01-05 04:37:03 UTC Re: Digitizing ccq@x... 2004-01-05 08:07:52 UTC Re: [CAD_CAM_EDM_DRO] Digitizing cnczeus 2004-01-05 09:20:29 UTC Re: Digitizing Alan Marconett KM6VV 2004-01-05 12:23:49 UTC Re: [CAD_CAM_EDM_DRO] Re: Digitizing Graham Stabler 2004-01-06 04:45:09 UTC Re: Digitizing Alan Marconett KM6VV 2004-01-06 12:20:10 UTC Re: [CAD_CAM_EDM_DRO] Re: Digitizing alex 2004-01-06 12:32:32 UTC Re: [CAD_CAM_EDM_DRO] Re: Digitizing Alan Marconett KM6VV 2004-01-06 12:51:45 UTC Re: [CAD_CAM_EDM_DRO] Re: Digitizing alex 2004-01-06 13:52:08 UTC Re: [CAD_CAM_EDM_DRO] Re: Digitizing Alan Marconett KM6VV 2004-01-06 15:29:08 UTC Re: [CAD_CAM_EDM_DRO] Re: Digitizing alex 2004-01-06 15:37:24 UTC Re: [CAD_CAM_EDM_DRO] Re: Digitizing Graham Stabler 2004-01-06 17:05:46 UTC Re: Digitizing alex 2004-01-06 17:11:07 UTC Re: [CAD_CAM_EDM_DRO] Re: Digitizing Alan Marconett KM6VV 2004-01-06 17:15:10 UTC Re: [CAD_CAM_EDM_DRO] Re: Digitizing alex 2004-01-06 17:20:28 UTC Re: [CAD_CAM_EDM_DRO] Re: Digitizing