RE: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Posted by
Tim Goldstein
on 2001-03-26 11:18:40 UTC
With a 200 line encoder the jitter is only .45 deg. With a 20 tpi lead screw
(Sherline) and a direct drive this is only a movement of 0.0000625" at the
table which is too small to actually occur. Even with a 10 tpi screw and
direct drive it is only .000125" which is likely below the amount required
to actually move the table. So other than some buzzing I don't see where it
would make any difference.
Tim
[Denver, CO]
(Sherline) and a direct drive this is only a movement of 0.0000625" at the
table which is too small to actually occur. Even with a 10 tpi screw and
direct drive it is only .000125" which is likely below the amount required
to actually move the table. So other than some buzzing I don't see where it
would make any difference.
Tim
[Denver, CO]
> Dan,
>
> I remember you saying that with a 200 Cpr encoder, and the
> gecko drives,
> there is a lot of jitter on the motor when it is just sitting
> there. You
> recommended using a 500 line encoder.
>
> I am puzzled over why you do not stick to your 500 line
> encoder and just
> use a rate multiplying G340 drive? Wouldn't this allow you
> to keep your
> speed up?
>
> Tom Eldredge
>
> FAQ: http://www.ktmarketing.com/faq.html
Discussion Thread
lasernerd@h...
2001-03-25 10:54:40 UTC
Gecko + Servos + Taig Mill
Tim Goldstein
2001-03-25 11:15:45 UTC
RE: [CAD_CAM_EDM_DRO] Gecko + Servos + Taig Mill
lasernerd@h...
2001-03-25 14:30:38 UTC
Re: Gecko + Servos + Taig Mill
Peter Chen
2001-03-25 18:23:50 UTC
Gecko + Servos + Taig Mill
mariss92705@y...
2001-03-25 18:34:29 UTC
Re: Gecko + Servos + Taig Mill
lasernerd@h...
2001-03-25 19:36:13 UTC
Re: Gecko + Servos + Taig Mill
Tim Goldstein
2001-03-25 19:52:44 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
lasernerd@h...
2001-03-25 19:59:11 UTC
Re: Gecko + Servos + Taig Mill
lasernerd@h...
2001-03-25 20:08:51 UTC
Re: Gecko + Servos + Taig Mill
Jon Elson
2001-03-25 22:31:37 UTC
Re: [CAD_CAM_EDM_DRO] Gecko + Servos + Taig Mill
Jon Elson
2001-03-25 22:40:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Jon Elson
2001-03-25 22:52:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Jon Elson
2001-03-25 23:00:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
cadman@p...
2001-03-25 23:15:19 UTC
Re: Gecko + Servos + Taig Mill
Tony Jeffree
2001-03-25 23:54:50 UTC
Re: Gecko + Servos + Taig Mill
dkowalcz@i...
2001-03-26 05:09:51 UTC
Re: Gecko + Servos + Taig Mill
Dan Mauch
2001-03-26 06:45:16 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Dan Mauch
2001-03-26 07:17:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Jeff Demand
2001-03-26 08:36:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Tom Eldredge
2001-03-26 11:02:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Tim Goldstein
2001-03-26 11:18:40 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Jon Elson
2001-03-26 13:21:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Tim Goldstein
2001-03-26 13:36:14 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Jon Elson
2001-03-26 13:43:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
lasernerd@h...
2001-03-26 16:18:10 UTC
Re: Gecko + Servos + Taig Mill
Jon Elson
2001-03-26 21:41:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Tim Goldstein
2001-03-26 21:55:56 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Jon Elson
2001-03-26 22:17:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Tony Jeffree
2001-03-27 00:26:04 UTC
Re: Gecko + Servos + Taig Mill
Dan Mauch
2001-03-27 05:18:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Nicholas Carter and Felice Luftschein
2001-03-27 08:52:47 UTC
Re: Gecko + Servos + Taig Mill
Jon Elson
2001-03-27 13:37:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill