RE: [CAD_CAM_EDM_DRO] Gecko + Servos + Taig Mill
Posted by
Tim Goldstein
on 2001-03-25 11:15:45 UTC
Hello Robin,
I am sure you will get lots of advise, but for the most bang for the buck
here is what I would suggest:
I would suggest you look at the Gecko G320 drives (servos instead of
steppers. The performance is better, but they are a little more work to set
up) Get the case, power supply, and motors from Camtronics, the driver
software from Yeager Automation, and the CAD/CAM from IMService.
You can get motors cheaper if you cruise E-bay, but you have to know what
you are looking for. The Camtronics ones are reasonably prices and known to
work great.
Gecko
http://www.geckodrive.com
Camtronics
http://www.seanet.com/~dmauch/
Yeager Automation
http://www.yeagerautomation.com
IMService
http://www.imsrv.com
(Special pricing for the CAD CAM group, look for Fred Smiths postings here
and follow the link)
There are pictures of the Camtronics servo case with power supply on my
website at http://www.ktmarketing.com/CamtronicsServoCase.htm
Tim
[Denver, CO]
I am sure you will get lots of advise, but for the most bang for the buck
here is what I would suggest:
I would suggest you look at the Gecko G320 drives (servos instead of
steppers. The performance is better, but they are a little more work to set
up) Get the case, power supply, and motors from Camtronics, the driver
software from Yeager Automation, and the CAD/CAM from IMService.
You can get motors cheaper if you cruise E-bay, but you have to know what
you are looking for. The Camtronics ones are reasonably prices and known to
work great.
Gecko
http://www.geckodrive.com
Camtronics
http://www.seanet.com/~dmauch/
Yeager Automation
http://www.yeagerautomation.com
IMService
http://www.imsrv.com
(Special pricing for the CAD CAM group, look for Fred Smiths postings here
and follow the link)
There are pictures of the Camtronics servo case with power supply on my
website at http://www.ktmarketing.com/CamtronicsServoCase.htm
Tim
[Denver, CO]
> Hello all,
>
> I've been using a Haas VF-2 and an MHP CNC mill at work, and I've
> been bitten by the CNC bug - bad. I have a Taig mill in my basement.
> It's a manual machine. I'm thinking about retrofitting it for 3 axis
> CNC capability.
>
> I'm new to servos, so I'm not sure if they're what I'm looking for. I
> have a 3 axis CNC controller (steppers) right now, but it doesn't
> support very much power, and I'd like to up the amps on the mill. I
> do understand that I should not expect such high feed rates using the
> Taig, but it would be nice to have enough power under the hood for
> whatever I want to make.
>
> So, without further ado, here's my question: How much power should I
> be looking for in the servos, and where should I be looking? I have
> some Vexta 125 oz steppers and they seem pretty powerful, but I've
> heard the Taig likes 200+ oz. How does this transfer to servos?
>
> I'd like to change the Taig over to ballscrews, so I suppose this
> should be included to get a good answer.
>
> I'll be cutting everything from plastic to stainless steel on the
> mill. I'd like decent rapid feed rates (is 100ipm too much to ask
> for?).
>
> Sorry about the simple question. I'm a newbie to all this super-sexy
> CNC stuff :)
>
> Regards,
>
> Robin
>
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for
> the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
> FAQ: http://www.ktmarketing.com/faq.html
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>
Discussion Thread
lasernerd@h...
2001-03-25 10:54:40 UTC
Gecko + Servos + Taig Mill
Tim Goldstein
2001-03-25 11:15:45 UTC
RE: [CAD_CAM_EDM_DRO] Gecko + Servos + Taig Mill
lasernerd@h...
2001-03-25 14:30:38 UTC
Re: Gecko + Servos + Taig Mill
Peter Chen
2001-03-25 18:23:50 UTC
Gecko + Servos + Taig Mill
mariss92705@y...
2001-03-25 18:34:29 UTC
Re: Gecko + Servos + Taig Mill
lasernerd@h...
2001-03-25 19:36:13 UTC
Re: Gecko + Servos + Taig Mill
Tim Goldstein
2001-03-25 19:52:44 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
lasernerd@h...
2001-03-25 19:59:11 UTC
Re: Gecko + Servos + Taig Mill
lasernerd@h...
2001-03-25 20:08:51 UTC
Re: Gecko + Servos + Taig Mill
Jon Elson
2001-03-25 22:31:37 UTC
Re: [CAD_CAM_EDM_DRO] Gecko + Servos + Taig Mill
Jon Elson
2001-03-25 22:40:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Jon Elson
2001-03-25 22:52:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Jon Elson
2001-03-25 23:00:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
cadman@p...
2001-03-25 23:15:19 UTC
Re: Gecko + Servos + Taig Mill
Tony Jeffree
2001-03-25 23:54:50 UTC
Re: Gecko + Servos + Taig Mill
dkowalcz@i...
2001-03-26 05:09:51 UTC
Re: Gecko + Servos + Taig Mill
Dan Mauch
2001-03-26 06:45:16 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Dan Mauch
2001-03-26 07:17:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Jeff Demand
2001-03-26 08:36:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Tom Eldredge
2001-03-26 11:02:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Tim Goldstein
2001-03-26 11:18:40 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Jon Elson
2001-03-26 13:21:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Tim Goldstein
2001-03-26 13:36:14 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Jon Elson
2001-03-26 13:43:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
lasernerd@h...
2001-03-26 16:18:10 UTC
Re: Gecko + Servos + Taig Mill
Jon Elson
2001-03-26 21:41:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Tim Goldstein
2001-03-26 21:55:56 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Jon Elson
2001-03-26 22:17:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Tony Jeffree
2001-03-27 00:26:04 UTC
Re: Gecko + Servos + Taig Mill
Dan Mauch
2001-03-27 05:18:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Nicholas Carter and Felice Luftschein
2001-03-27 08:52:47 UTC
Re: Gecko + Servos + Taig Mill
Jon Elson
2001-03-27 13:37:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill