Re: Gecko + Servos + Taig Mill
Posted by
mariss92705@y...
on 2001-03-25 18:34:29 UTC
Hi,
Here's how to start, be it steppers or servos:
(1) How fast do you want to go (IPM) and how much push (Lbs) do you
want at that speed?
(2) Calculate the power needed: Watts = ( Lbs X IPM ) / 531
Ex: 400 Lbs at 250 IPM = 188 Watts
(3) If Watts are:
0 to 200, use a size 23 servomotor
200 to 500, use a size 34 servomotor
500 to 1000, use a size 42 servomotor
In the above example, a size 23 motor will do
(4) Servomotors usually have to be geared down because they develop
power at speeds higher than can be used for direct drive.
(5) Calculate the reduction ratio:
Motor no-load RPM / ( 1.25 X IPM x TPI ) : 1
Ex: 6000 RPM / ( 1.25 x 250 X 5 ) = 3.84 to 1 reduction
That should get you started.
Mariss
Here's how to start, be it steppers or servos:
(1) How fast do you want to go (IPM) and how much push (Lbs) do you
want at that speed?
(2) Calculate the power needed: Watts = ( Lbs X IPM ) / 531
Ex: 400 Lbs at 250 IPM = 188 Watts
(3) If Watts are:
0 to 200, use a size 23 servomotor
200 to 500, use a size 34 servomotor
500 to 1000, use a size 42 servomotor
In the above example, a size 23 motor will do
(4) Servomotors usually have to be geared down because they develop
power at speeds higher than can be used for direct drive.
(5) Calculate the reduction ratio:
Motor no-load RPM / ( 1.25 X IPM x TPI ) : 1
Ex: 6000 RPM / ( 1.25 x 250 X 5 ) = 3.84 to 1 reduction
That should get you started.
Mariss
--- In CAD_CAM_EDM_DRO@y..., lasernerd@h... wrote:
> Hello all,
> snip <
> So, without further ado, here's my question: How much power should
I
> be looking for in the servos, and where should I be looking? I have
> some Vexta 125 oz steppers and they seem pretty powerful, but I've
> heard the Taig likes 200+ oz. How does this transfer to servos?
>
> I'd like to change the Taig over to ballscrews, so I suppose this
> should be included to get a good answer.
>
> I'll be cutting everything from plastic to stainless steel on the
> mill. I'd like decent rapid feed rates (is 100ipm too much to ask
> for?).
>
> Sorry about the simple question. I'm a newbie to all this super-
sexy
> CNC stuff :)
>
> Regards,
>
> Robin
Discussion Thread
lasernerd@h...
2001-03-25 10:54:40 UTC
Gecko + Servos + Taig Mill
Tim Goldstein
2001-03-25 11:15:45 UTC
RE: [CAD_CAM_EDM_DRO] Gecko + Servos + Taig Mill
lasernerd@h...
2001-03-25 14:30:38 UTC
Re: Gecko + Servos + Taig Mill
Peter Chen
2001-03-25 18:23:50 UTC
Gecko + Servos + Taig Mill
mariss92705@y...
2001-03-25 18:34:29 UTC
Re: Gecko + Servos + Taig Mill
lasernerd@h...
2001-03-25 19:36:13 UTC
Re: Gecko + Servos + Taig Mill
Tim Goldstein
2001-03-25 19:52:44 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
lasernerd@h...
2001-03-25 19:59:11 UTC
Re: Gecko + Servos + Taig Mill
lasernerd@h...
2001-03-25 20:08:51 UTC
Re: Gecko + Servos + Taig Mill
Jon Elson
2001-03-25 22:31:37 UTC
Re: [CAD_CAM_EDM_DRO] Gecko + Servos + Taig Mill
Jon Elson
2001-03-25 22:40:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Jon Elson
2001-03-25 22:52:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Jon Elson
2001-03-25 23:00:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
cadman@p...
2001-03-25 23:15:19 UTC
Re: Gecko + Servos + Taig Mill
Tony Jeffree
2001-03-25 23:54:50 UTC
Re: Gecko + Servos + Taig Mill
dkowalcz@i...
2001-03-26 05:09:51 UTC
Re: Gecko + Servos + Taig Mill
Dan Mauch
2001-03-26 06:45:16 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Dan Mauch
2001-03-26 07:17:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Jeff Demand
2001-03-26 08:36:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Tom Eldredge
2001-03-26 11:02:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Tim Goldstein
2001-03-26 11:18:40 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Jon Elson
2001-03-26 13:21:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Tim Goldstein
2001-03-26 13:36:14 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Jon Elson
2001-03-26 13:43:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
lasernerd@h...
2001-03-26 16:18:10 UTC
Re: Gecko + Servos + Taig Mill
Jon Elson
2001-03-26 21:41:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Tim Goldstein
2001-03-26 21:55:56 UTC
RE: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Jon Elson
2001-03-26 22:17:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Tony Jeffree
2001-03-27 00:26:04 UTC
Re: Gecko + Servos + Taig Mill
Dan Mauch
2001-03-27 05:18:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill
Nicholas Carter and Felice Luftschein
2001-03-27 08:52:47 UTC
Re: Gecko + Servos + Taig Mill
Jon Elson
2001-03-27 13:37:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: Gecko + Servos + Taig Mill