Re: [CAD_CAM_EDM_DRO] Re: Swiss turning conversion
Posted by
Jon Anderson
on 2001-04-25 08:55:30 UTC
Smoke wrote:
third swung on a short arm which was clamped in place with a KantTwist
clamp. Crude, but it worked fine. The cross slide was used to center
everything on the stock. The cutting tool sat in a square hole and was
backed up by a 40 pitch screw allowing fine adjustment of the final
diameter.
Of course, for a CNC app, the supports must be independant of the tool!
Jon
>Probably a hundred ways to approach it! I had two fixed bearings, the
> I like the roller bearing idea Jon , but...I'd use a scissors type
> mount for the bearings similar to those available for doing knurling.
third swung on a short arm which was clamped in place with a KantTwist
clamp. Crude, but it worked fine. The cross slide was used to center
everything on the stock. The cutting tool sat in a square hole and was
backed up by a 40 pitch screw allowing fine adjustment of the final
diameter.
Of course, for a CNC app, the supports must be independant of the tool!
Jon
Discussion Thread
stratton@m...
2001-04-24 19:13:57 UTC
Swiss turning conversion
dougrasmussen@c...
2001-04-24 19:35:23 UTC
Re: Swiss turning conversion
ptengin@a...
2001-04-24 19:46:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Swiss turning conversion
Jon Anderson
2001-04-24 20:07:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: Swiss turning conversion
dougrasmussen@c...
2001-04-24 20:42:24 UTC
Re: Swiss turning conversion
dougrasmussen@c...
2001-04-24 21:09:36 UTC
Re: Swiss turning conversion
stratton@m...
2001-04-24 21:34:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: Swiss turning conversion
Jon Anderson
2001-04-24 23:37:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: Swiss turning conversion
Jon Anderson
2001-04-24 23:40:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: Swiss turning conversion
Ian Wright
2001-04-25 01:39:32 UTC
Re: [CAD_CAM_EDM_DRO] Swiss turning conversion
Sven Peter, TAD S.A.
2001-04-25 06:49:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: Swiss turning conversion
Smoke
2001-04-25 07:35:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Swiss turning conversion
Jon Anderson
2001-04-25 08:55:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: Swiss turning conversion
dougrasmussen@c...
2001-04-25 10:07:23 UTC
Re: Swiss turning conversion
Jon Anderson
2001-04-25 11:00:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: Swiss turning conversion
Drew Rogge
2001-04-25 11:12:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: Swiss turning conversion
Smoke
2001-04-25 11:27:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: Swiss turning conversion
ptengin@a...
2001-04-25 14:14:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: Swiss turning conversion
ballendo@y...
2001-04-25 22:21:09 UTC
Re: Swiss turning conversion
Chris Paine
2001-04-27 16:45:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: Swiss turning conversion
Sven Peter, TAD S.A.
2001-04-27 20:48:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: Swiss turning conversion