Re: [CAD_CAM_EDM_DRO] Request help from group
Posted by
STAN MCDONALD
on 2001-07-23 07:31:09 UTC
Can you email me a picture of what you did?
I need the table to rotate 200 degrees min and 270 perfered. Then when it is
done i would press a lever and it would return.
Thanks
Stan
Doug Harrison wrote:
I need the table to rotate 200 degrees min and 270 perfered. Then when it is
done i would press a lever and it would return.
Thanks
Stan
Doug Harrison wrote:
> Stan;
>
> I have an air cylinder operated index table. It uses a ratchet and pawl
> escapement. The maximum angle is limited to about 90 degrees. If the table
> need only move in one direction you can use such a mechanism and fire it
> twice for each 180.
>
> If you need the table to return when the cylinder does then you could use a
> 2:1 gear increase - say fifty teeth on the table and 100 teeth on the gear
> actuated by the cylinder as a crank. Put your stops on the table for
> limiting rotation to 180 degrees.
>
> Doug
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
Discussion Thread
STAN MCDONALD
2001-07-22 18:45:10 UTC
Request help from group
Smoke
2001-07-22 19:03:58 UTC
Re: [CAD_CAM_EDM_DRO] Request help from group
Smoke
2001-07-22 19:13:09 UTC
Re: [CAD_CAM_EDM_DRO] Request help from group
Doug Harrison
2001-07-22 19:28:10 UTC
Re: [CAD_CAM_EDM_DRO] Request help from group
Ian Wright
2001-07-23 00:25:26 UTC
Re: [CAD_CAM_EDM_DRO] Request help from group
STAN MCDONALD
2001-07-23 07:31:09 UTC
Re: [CAD_CAM_EDM_DRO] Request help from group
STAN MCDONALD
2001-07-23 07:31:36 UTC
Re: [CAD_CAM_EDM_DRO] Request help from group
Smoke
2001-07-23 08:13:25 UTC
Re: [CAD_CAM_EDM_DRO] Request help from group
Smoke
2001-07-23 08:38:32 UTC
Re: [CAD_CAM_EDM_DRO] Request help from group
Ethan Vos
2001-07-23 09:10:26 UTC
RE: [CAD_CAM_EDM_DRO] Request help from group
mclem@b...
2001-07-23 16:57:15 UTC
Re: Request help from group
dougrasmussen@c...
2001-07-23 19:04:56 UTC
Re: Request help from group
Sven Peter, TAD S.A.
2001-07-23 20:29:59 UTC
Re: [CAD_CAM_EDM_DRO] Request help from group
ballendo@y...
2001-07-25 00:27:09 UTC
Re: Request help from group