Re: Request help from group
Posted by
ballendo@y...
on 2001-07-25 00:27:09 UTC
Hello,
FWIW, I have not read all the responses in this thread. Why not use
TWO linear type cylinders? Arranged like "stages" of a rocket. Let
the arm move independant of the rotating table and its base. One
cylinder goes from base to arm, the next goes from arm to table.
Since each will give almost 180° of travel, the 200° need is easily
met. "Wire" them together if it is simply an "end position required"
setup, or use sequential air logic if necessary.
Hope this helps.
Ballendo
FWIW, I have not read all the responses in this thread. Why not use
TWO linear type cylinders? Arranged like "stages" of a rocket. Let
the arm move independant of the rotating table and its base. One
cylinder goes from base to arm, the next goes from arm to table.
Since each will give almost 180° of travel, the 200° need is easily
met. "Wire" them together if it is simply an "end position required"
setup, or use sequential air logic if necessary.
Hope this helps.
Ballendo
--- In CAD_CAM_EDM_DRO@y..., STAN MCDONALD <SMCDONAL@K...> wrote:
> > >Hello list I am working on a project and need to request your
assistance. I
> > >am atempting to make a rotary turning table to be driven by an
air cylinder
> > >and I need to have the cylinder be retracted and then when fully
extended
> > >have the table have moved min 200 degrees or more. The problem I
have run
> > >into is when the cylinder has moved the table 180 degrees ( how
do we
> > >position the cylinder so that we would not need to stop remove
the cylinder
> > >and then retract the cylinder with it on the other side of
center?
> > >
> > >The table is a 1-1/2" thick plate cut round 14-15" in dia made
of steel. I
> > >have an arm stuck out one side to connect whatever to and the
whole thing
> > is
> > >resting on some bearings for movment (similar to a car front
axel).
> > >
> > >Thanks
> > >
> > >Stan
Discussion Thread
STAN MCDONALD
2001-07-22 18:45:10 UTC
Request help from group
Smoke
2001-07-22 19:03:58 UTC
Re: [CAD_CAM_EDM_DRO] Request help from group
Smoke
2001-07-22 19:13:09 UTC
Re: [CAD_CAM_EDM_DRO] Request help from group
Doug Harrison
2001-07-22 19:28:10 UTC
Re: [CAD_CAM_EDM_DRO] Request help from group
Ian Wright
2001-07-23 00:25:26 UTC
Re: [CAD_CAM_EDM_DRO] Request help from group
STAN MCDONALD
2001-07-23 07:31:09 UTC
Re: [CAD_CAM_EDM_DRO] Request help from group
STAN MCDONALD
2001-07-23 07:31:36 UTC
Re: [CAD_CAM_EDM_DRO] Request help from group
Smoke
2001-07-23 08:13:25 UTC
Re: [CAD_CAM_EDM_DRO] Request help from group
Smoke
2001-07-23 08:38:32 UTC
Re: [CAD_CAM_EDM_DRO] Request help from group
Ethan Vos
2001-07-23 09:10:26 UTC
RE: [CAD_CAM_EDM_DRO] Request help from group
mclem@b...
2001-07-23 16:57:15 UTC
Re: Request help from group
dougrasmussen@c...
2001-07-23 19:04:56 UTC
Re: Request help from group
Sven Peter, TAD S.A.
2001-07-23 20:29:59 UTC
Re: [CAD_CAM_EDM_DRO] Request help from group
ballendo@y...
2001-07-25 00:27:09 UTC
Re: Request help from group