RE: [CAD_CAM_EDM_DRO] collets

Thanks Rich; a neighbor (retired engineer) suggested this but so far I've
only found 5c's of this type and the internal bore (thread) is larger than
the OD I need. Suggestion as to where to find one?

Thanks again

Lew

-----Original Message-----
From: Rich D. [mailto:cmsteam@...]
Sent: Wednesday, November 07, 2001 10:37 PM
To: CAD_CAM_EDM_DRO@yahoogroups.com
Subject: Re: [CAD_CAM_EDM_DRO] collets

Lew.
If you say an R8 will have enough meat in it, buy an "emergenecy" (soft)
collet as this is intended to be machined.
RichD

LEW BEST wrote:

>
> Hi All
>
> Sorry to post this to so many lists, I know some of you are on multiple
> lists and this will get repetitious.
>
> I need to try to make a collet. The design is like a 5C with external
> threads but much smaller. An R8 is only slightly larger in outside

diameter

> (I thought I might be able to turn down and externally thread an R8, would
> also need to slightly flatten the nose taper. However after reading the
> specs in the Mcmaster catalog I feel they are probably too hard steel to
> turn.
>
> The collet I need is for a Black Diamond 31 drill grinder, is the large
> collet that holds the larger bushings and the 3/4" bit for sharpening. BD
> wants $120 some-odd for the one collet so I'd like to try to turn one
> myself.
>
> All it does is hold the bit in place for sharpening it, no high torque as

in

> milling, drilling, etc. I'd appreciate any suggestions as to material to
> use, how to cut the 3 thin slots on the face that allow it to tighten,

etc.

> BTW my eq is all manual, even though the CAD CAM group is included in the
> list. I get good info from all the lists!
>
> Thanks
>
> Lew
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/

--
~ ~~ ~ ~ ~~ ~~____~,~~ ~~~~
\------/ |00|_[]_[]__||0
.|_CMRy_|-|__|________|_|,
__________''oo__oo__---"0=0=0"=o[]o\\______________________________
-==Rich=-=Colorado Midland Railway=-=cmsteam@...=-Atlanta-
----------See my web site: <http://cmsteamer.homestead.com/> ------

Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/

Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
Moderator: jmelson@... timg@... [Moderator]
URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
bill,
List Manager



Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/