CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: collets

Posted by Marcus & Eva
on 2001-11-09 19:37:17 UTC
Hi Doug:
Which part of the collet do you think is difficult to make?
I've made them with concentricity down to 0.0001" or better without any
trouble at all.
Some of my homemade wonders are better for runout than the Lyndex collets I
can buy.
Course they cost a lot more to make than to buy when you factor in your shop
rate, so I only make what I can't get any other way.
But it's really not a difficult job.

Cheers

Marcus
-----Original Message-----
From: dougrasmussen@... <dougrasmussen@...>
To: CAD_CAM_EDM_DRO@yahoogroups.com <CAD_CAM_EDM_DRO@yahoogroups.com>
Date: Friday, November 09, 2001 8:12 AM
Subject: [CAD_CAM_EDM_DRO] Re: collets


>--- In CAD_CAM_EDM_DRO@y..., Sven Peter <peteryco@r...> wrote:
>Sven,
>
>I'm very pessimistic when people tell me they have success making
>collets with the typical lathe/mill setups in home shops. Sorry
>guys, but I lump you into the same group as those who tell me they
>can sharpen drills by hand as well as can be done on drill sharpening
>machines.
>
>Doug
>
>
>> Hi Ian,
>> I have seen a lot of machines and a few big ones but nothing
>compared
>> with this. My tries always ran out of center without cylindrical
>> grinder. And even sometimes with it.
>> Have fun making collets.
>> Sven Peter
>>
>> Iain Ward wrote:
>> >
>> > I do not have to worry about drill wander over the 29" length of
>> > the collet.
>> > Damnedest thing I've seen, 20" draw bar on a 29" long collet. The
>> > spindle bore is trumpet shaped and has 16" of contact surface for
>> > compressing the collet.
>> >
>> > Sorry for the ramble, but hopefully it helps.
>> >
>> > Iain
>> >
>
>
>Addresses:
>FAQ: http://www.ktmarketing.com/faq.html
>FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
>Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
>Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
>Moderator: jmelson@... timg@... [Moderator]
>URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>bill,
>List Manager
>
>
>
>Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>

Discussion Thread

LEW BEST 2001-11-07 19:13:17 UTC collets Rich D. 2001-11-07 20:37:20 UTC Re: [CAD_CAM_EDM_DRO] collets LEW BEST 2001-11-07 20:46:14 UTC RE: [CAD_CAM_EDM_DRO] collets Rich D. 2001-11-07 21:11:23 UTC Re: [CAD_CAM_EDM_DRO] collets LEW BEST 2001-11-07 21:14:03 UTC RE: [CAD_CAM_EDM_DRO] collets Marcus & Eva 2001-11-07 21:24:53 UTC Re: [CAD_CAM_EDM_DRO] collets dkowalcz@d... 2001-11-07 22:02:26 UTC Re: collets Christopher Coley 2001-11-08 08:00:20 UTC MAXNC 10 Smoke 2001-11-08 09:34:56 UTC Re: [CAD_CAM_EDM_DRO] collets Alan Marconett KM6VV 2001-11-08 13:51:39 UTC Re: [CAD_CAM_EDM_DRO] MAXNC 10 Christopher Coley 2001-11-08 13:53:39 UTC RE: [CAD_CAM_EDM_DRO] MAXNC 10 Alan Marconett KM6VV 2001-11-08 15:10:04 UTC Re: [CAD_CAM_EDM_DRO] MAXNC 10 dougrasmussen@c... 2001-11-08 19:06:26 UTC Re: collets LEW BEST 2001-11-08 19:27:22 UTC RE: [CAD_CAM_EDM_DRO] Re: collets LEW BEST 2001-11-09 04:47:04 UTC RE: [CAD_CAM_EDM_DRO] Re: collets Iain Ward 2001-11-09 05:20:01 UTC Re: [CAD_CAM_EDM_DRO] Re: collets Sven Peter 2001-11-09 06:22:35 UTC Re: [CAD_CAM_EDM_DRO] Re: collets dougrasmussen@c... 2001-11-09 08:12:51 UTC Re: collets Sven Peter 2001-11-09 10:58:47 UTC Re: [CAD_CAM_EDM_DRO] Re: collets Iain Ward 2001-11-09 17:46:33 UTC Re: [CAD_CAM_EDM_DRO] Re: collets Marcus & Eva 2001-11-09 19:37:17 UTC Re: [CAD_CAM_EDM_DRO] Re: collets dougrasmussen@c... 2001-11-09 21:29:42 UTC Re: collets Marcus & Eva 2001-11-10 09:08:56 UTC Re: [CAD_CAM_EDM_DRO] Re: collets ccs@m... 2001-11-10 09:26:55 UTC Re: [CAD_CAM_EDM_DRO] Re: collets Fred Smith 2001-11-10 10:11:34 UTC Re: collets dougrasmussen@c... 2001-11-10 17:00:12 UTC Re: collets Fred Smith 2001-11-10 17:13:44 UTC Re: collets ccs@m... 2001-11-10 17:16:17 UTC Re: [CAD_CAM_EDM_DRO] Re: collets Marcus & Eva 2001-11-10 19:01:50 UTC Re: [CAD_CAM_EDM_DRO] Re: collets Ian Wright 2001-11-13 15:48:06 UTC Re: [CAD_CAM_EDM_DRO] Re: collets Marcus & Eva 2001-11-13 21:25:19 UTC Re: [CAD_CAM_EDM_DRO] Re: collets Ian Wright 2001-11-14 02:38:26 UTC Re: [CAD_CAM_EDM_DRO] Re: collets Smoke 2001-11-14 08:02:12 UTC Re: [CAD_CAM_EDM_DRO] Re: collets