Re: New member new to cnc.
Posted by
Alan Marconett KM6VV
on 2002-01-11 23:06:10 UTC
Hi Ballendo,
Why an aluminum "box", and where would you find it?
I'd definitely agree on the 5400 over the 200 for CNC. The Rotary table
is a good addition, 'tho.
Alan KM6VV
ballendo wrote:
Why an aluminum "box", and where would you find it?
I'd definitely agree on the 5400 over the 200 for CNC. The Rotary table
is a good addition, 'tho.
Alan KM6VV
ballendo wrote:
>
> Graham,
>
> Some have had problems withthe 2000 mill twisting on its column
> during cuts. There was some discussion on the sherline yahoo gorup
> awhile back.
>
> Also, the 5400 presents a more "known" setup than the myriad of
> adjustments that have to be checked and re-checked when using the
> 2000. Now, that's not any different than a "real" mill, but even the
> large cnc machines do away with most of the "adjustability" so that
> the machine/cutter location is more easily established/determined...
>
> Lastly, if you clamp a 2x6x1/4 wall, 12 inch long, rectangular
> alum "box" extrusion to the table of a 5400 and use the horizontal
> milling base accessory from Sherline; you will have a large area to
> work AND the "dust" will tend to fall away due to gravity. This
> technique also works well for other "flat" workpieces, like pc
> boards...
>
> Hope this helps.
>
> Ballendo
Discussion Thread
snokket
2002-01-10 12:52:48 UTC
New member new to cnc.
j.guenther
2002-01-10 13:07:09 UTC
RE: [CAD_CAM_EDM_DRO] New member new to cnc.
Scot Rogers
2002-01-10 13:08:25 UTC
vfd
snokket
2002-01-10 14:27:59 UTC
Re: New member new to cnc.
ballendo
2002-01-11 17:31:00 UTC
Re: New member new to cnc.
Alan Marconett KM6VV
2002-01-11 23:06:10 UTC
Re: New member new to cnc.
ballendo
2002-01-12 05:48:50 UTC
alum. box "table" for sherline was Re: New member new to cnc.
snokket
2002-01-13 14:50:06 UTC
Re: New member new to cnc. ( Thanks ballendo )
ballendo
2002-01-16 05:57:51 UTC
Re: New member new to cnc. ( Thanks ballendo )
snokket
2002-01-16 14:23:52 UTC
Re: New member new to cnc. ( Thanks ballendo )
tom mazz
2002-03-06 05:38:41 UTC
vfd
Richard Rogers
2002-03-06 05:46:10 UTC
Re: [CAD_CAM_EDM_DRO] vfd
Dr Brian H Le Page
2002-03-06 20:31:05 UTC
RE: [CAD_CAM_EDM_DRO] vfd
Jon Elson
2002-03-06 23:33:32 UTC
Re: [CAD_CAM_EDM_DRO] vfd
Sven Peter
2002-03-07 05:39:44 UTC
Re: [CAD_CAM_EDM_DRO] vfd
Jon Elson
2002-03-07 10:00:32 UTC
Re: [CAD_CAM_EDM_DRO] vfd
Unterhausen Umberto
2002-03-07 18:24:46 UTC
vfd