Re: [CAD_CAM_EDM_DRO] EMC Contouring Settings
Posted by
Jon Elson
on 2002-01-29 22:31:06 UTC
Chris L wrote:
is usually set to near the maximum for the motion system, but
leaves enough reserve so the steppers don't stall or the
servos don't trip.
Then, in the G-code, you have a choice of continuous contouring
or exact stop mode, which assures that every move has completed
to the endpoint before the next move is begun.
That is all that I know about.
Jon
> Greetings,With EMC, there is an acceleration parameter in the .ini file that
>
> I am wondering if anyone running EMC will indicate what "options" there
> are to adjust for the continuous contouring features of EMC.
>
> Typically, The simultaneous "start/stop" rate(s), "acceleration" Rate
> and Contouring "tolerance" has quite a bit of reliance on each other.
> Changing one has an effect on another.
>
> FlashCut offers the above 3, where typically you run the "tolerance"
> above the Start/Stop rates as high as possible without smashing thru
> corners. Obviously, the "Start/Stop is adjusted to reflect the maximum
> capabilities your drive mechanism has to start and stop the machine.
>
> Indexer too, uses a similar "V-Shift" rate. I never saw a control that
> allowed the input of "angular" information to indicate contouring
> capability or any control that allowed for more than one "level" of
> contouring based on "angle" or tolerance.
>
> So, I am curious what the associated settings are in EMC.
is usually set to near the maximum for the motion system, but
leaves enough reserve so the steppers don't stall or the
servos don't trip.
Then, in the G-code, you have a choice of continuous contouring
or exact stop mode, which assures that every move has completed
to the endpoint before the next move is begun.
That is all that I know about.
Jon
Discussion Thread
Chris L
2002-01-29 21:43:35 UTC
EMC Contouring Settings
Jon Elson
2002-01-29 22:31:06 UTC
Re: [CAD_CAM_EDM_DRO] EMC Contouring Settings
Chris L
2002-01-29 23:10:41 UTC
Re: [CAD_CAM_EDM_DRO] EMC Contouring Settings
awemawson
2002-01-30 00:58:38 UTC
Re: EMC Contouring Settings
Gene
2002-01-30 01:56:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Contouring Settings
chewy8833
2002-01-30 06:22:57 UTC
Re: EMC Contouring Settings/ downloading BDI
Richard Konnen
2002-01-30 08:13:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Contouring Settings/ downloading BDI
Engine Tech
2002-01-30 08:53:21 UTC
RE: [CAD_CAM_EDM_DRO] Re: EMC Contouring Settings/ downloading BDI
ballendo
2002-01-30 09:05:42 UTC
Re: EMC Contouring Settings/ downloading BDI
Mike Gann
2002-01-30 09:11:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Contouring Settings/ downloading BDI
Chris L
2002-01-30 17:00:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Contouring Settings
Chris L
2002-01-30 18:08:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Contouring Settings/ downloading BDI
Art Fenerty
2002-01-30 18:35:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Contouring Settings/ downloading BDI
Jon Elson
2002-01-30 22:48:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Contouring Settings/ downloading BDI
Art Fenerty
2002-02-01 13:53:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Contouring Settings/ downloading BDI
ballendo
2002-02-01 15:12:25 UTC
Re: EMC Contouring Settings/ downloading BDI
Art Fenerty
2002-02-01 15:25:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Contouring Settings/ downloading BDI
Alan Marconett KM6VV
2002-02-01 16:03:17 UTC
Re: EMC Contouring Settings/ downloading BDI
Art Fenerty
2002-02-01 16:47:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Contouring Settings/ downloading BDI
dkowalcz2000
2002-02-01 20:50:03 UTC
Re: EMC Contouring Settings/ downloading BDI
Jon Elson
2002-02-01 22:25:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Contouring Settings/ downloading BDI
Jon Elson
2002-02-01 23:06:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Contouring Settings/ downloading BDI
Bill Vance
2002-02-02 02:02:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Contouring Settings/ downloading BDI
Art Fenerty
2002-02-02 06:24:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Contouring Settings/ downloading BDI
Art Fenerty
2002-02-02 07:06:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Contouring Settings/ downloading BDI
Alan Marconett KM6VV
2002-02-02 09:13:37 UTC
Re: EMC Contouring Settings/ downloading BDI
Jon Elson
2002-02-02 09:56:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Contouring Settings/ downloading BDI
Jon Elson
2002-02-02 10:01:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Contouring Settings/ downloading BDI
Art Fenerty
2002-02-02 10:48:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Contouring Settings/ downloading BDI
Paul
2002-02-02 13:31:39 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Contouring Settings/ downloading BDI
Bill Vance
2002-02-02 14:09:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC Contouring Settings/ downloading BDI
ballendo
2002-02-03 01:43:45 UTC
Universal head was Re: EMC Contouring Settings/ downloading BDI
Bill Vance
2002-02-03 05:24:55 UTC
Re: [CAD_CAM_EDM_DRO] Universal head was Re: EMC Contouring Settings/ downloading BDI
Hugh Currin
2002-02-03 09:26:30 UTC
Re: Universal head was
ballendo
2002-02-04 08:09:08 UTC
Re: Universal head was