CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Linux box

Posted by Paul
on 2002-04-06 14:40:59 UTC
Hi Hoyt

I dare say BDI could be transfered to floppies - Lots of them....
The standard BDI occupies some 540Mb, whilst BDI-TNG just about fills two
CDs. With only a 200MHz processor, I wouldn't recommend the TNG as it does
not have steppermod - Pity really, as you could have done an upgrade on top
of the RH7.1.
For running stepper motors, the parallel ports are used to output the
step/dir signals. Servos can either use Jon's parallel port interface or a
Servo To Go card.

Regards Paul.


On Saturday 06 April 2002 17:50, batwings@... wrote:
> Well, to make a long one short, I saw a 200 mH with 96 meg RAM, 6 giga HD
> and 7.1 RedHat. So I bought it cheap. Is BDI available on 3.5" floppy?
> Where do the signals to the machine come out?

Discussion Thread

resosys 2002-03-27 20:46:29 UTC motor grounding and DB9 connector question Tim Goldstein 2002-03-27 20:53:24 UTC RE: [CAD_CAM_EDM_DRO] motor grounding and DB9 connector question resosys 2002-03-27 21:13:02 UTC Re: motor grounding and DB9 connector question Doug Fortune 2002-03-27 21:13:52 UTC Re: [CAD_CAM_EDM_DRO] motor grounding and DB9 connector question resosys 2002-03-27 21:24:12 UTC Re: motor grounding and DB9 connector question Chris L 2002-03-27 21:49:25 UTC Re: [CAD_CAM_EDM_DRO] Re: motor grounding and DB9 connector question Jerry Biehler 2002-03-27 21:50:25 UTC Re: [CAD_CAM_EDM_DRO] Re: motor grounding and DB9 connector question aspaguy 2002-03-27 21:58:37 UTC Re: motor grounding and DB9 connector question Jon Elson 2002-03-28 00:14:28 UTC Re: [CAD_CAM_EDM_DRO] Re: motor grounding and DB9 connector question dave_ace_me 2002-03-28 05:09:18 UTC switching motors (was Re: motor grounding and DB9 connector question Doug Fortune 2002-03-28 07:09:26 UTC Re: [CAD_CAM_EDM_DRO] Re: motor grounding and DB9 connector question Henrik Olsson 2002-03-28 07:39:57 UTC Re: [CAD_CAM_EDM_DRO] Re: motor grounding and DB9 connector question Henrik Olsson 2002-03-28 07:55:27 UTC Re: [CAD_CAM_EDM_DRO] Re: motor grounding and DB9 connector question resosys 2002-03-28 08:05:26 UTC Re: motor grounding and DB9 connector question Low Cost Equipment Project 2002-03-28 08:06:01 UTC Re: [CAD_CAM_EDM_DRO] motor grounding and DB9 connector question resosys 2002-03-28 08:13:58 UTC Re: motor grounding and DB9 connector question Jon Elson 2002-03-28 09:57:17 UTC Re: [CAD_CAM_EDM_DRO] Re: motor grounding and DB9 connector question Jon Elson 2002-03-28 10:02:27 UTC Re: [CAD_CAM_EDM_DRO] Re: motor grounding and DB9 connector question beer@s... 2002-03-28 11:42:18 UTC Re: motor grounding and DB9 connector question JanRwl@A... 2002-03-28 20:21:20 UTC Re: [CAD_CAM_EDM_DRO] motor grounding and DB9 connector question Henrik Olsson 2002-03-29 05:15:11 UTC Re: [CAD_CAM_EDM_DRO] Re: motor grounding and DB9 connector question ballendo 2002-04-06 06:03:36 UTC Re: motor grounding and DB9 connector question ballendo 2002-04-06 06:19:46 UTC Re: motor grounding and DB9 connector question batwings@i... 2002-04-06 14:23:39 UTC Linux box Paul 2002-04-06 14:40:59 UTC Re: [CAD_CAM_EDM_DRO] Linux box Jon Elson 2002-04-06 21:59:42 UTC Re: [CAD_CAM_EDM_DRO] Linux box batwings@i... 2002-04-07 05:22:53 UTC bloat Paul 2002-04-07 07:27:52 UTC Re: [CAD_CAM_EDM_DRO] bloat batwings@i... 2002-04-07 08:43:01 UTC Re: [CAD_CAM_EDM_DRO] bloat Tim Goldstein 2002-04-07 11:44:43 UTC RE: [CAD_CAM_EDM_DRO] bloat Stan Stocker 2002-04-07 12:44:25 UTC Re: [CAD_CAM_EDM_DRO] bloat Jon Elson 2002-04-07 13:45:00 UTC Re: [CAD_CAM_EDM_DRO] bloat