CAD CAM EDM DRO - Yahoo Group Archive

leadscrew protectors ( was Re: telescoping leadscrew protectors

Posted by aspaguy
on 2002-04-15 21:17:28 UTC
Dryer tube comes in 4-6" and white color I believe. If you want 3"
try RV sewer tube. It comes in pretty bright blue. Downside is when
the neighbor with the $60,000 moterhome wanders into your garage you
will be known as the guy with the contraption you built outta "poop
shute" Then its all "Ya might be a redneck if....."
Have Fun.
Dale


--- In CAD_CAM_EDM_DRO@y..., "ballendo" <ballendo@y...> wrote:
> Dave,
>
> Promise not to laugh...
>
> Clothes Dryer vent hose. Yes, it's too big, ugly, and light duty...
>
> Also cheap, widely available, and VERY compressible.
>
> And if the diameter is too big for ya, take a trip to your
> local "rubber and hose" industrial supplier. There are more than a
> few commercial hoses designed to compress in the length direction.
> This will also be a source fo rthose with higher operating specs,
as
> many different types of material are used and available as well;
> including oil resistant types.
>
> Hope this helps,
>
> Ballendo
>
> --- In CAD_CAM_EDM_DRO@y..., "dave_ace_me" <davemucha@j...> wrote:
> > I agree, some parts of this business is just womens work. :" )
> >
> > I looked at using a self winding roll to be uded to keep the
chips
> > away but that was a flat top and would actually hold the small
> chips
> > until it would pass some sort of angle to let them fall.
> >
> > My chips are cold, so plastic or rubber would work but I did not
> like
> > the cost of the rubber bellows. I tried to find some from a TV
> Dish
> > style linear actuator, nice length, but they seem to range around
> > $20.00 a foot for the stuff.
> >
> > I opted for what I had on hand and may still switch to an
inverted
> V
> > for the simplicity and also access.
> >
> > Dave
> >
> >
> >
> >
> >
> > --- In CAD_CAM_EDM_DRO@y..., "Mike Snodgrass" <snarf@s...> wrote:
> > >
> > > ----- Original Message -----
> > > From: "Sven Peter" <peteryco@r...>
> > > To: <CAD_CAM_EDM_DRO@y...>
> > > Sent: Friday, April 12, 2002 7:11 AM
> > > Subject: Re: [CAD_CAM_EDM_DRO] telescoping leadscrew protectors
> > >
> > > I have, and I know you can get long " bellows" type protectors
in
> > many
> > > sizes. They are used to protect hydraulic cylinder shafts, I
> > think they
> > > are expensive though it would be easy for a woman with a sewing
> > machine and
> > > some good apolstery material. You can get the new ones from a
> > hydraulic
> > > dealer.
> > >
> > >
> > >
> > >
> > >
> > > > Hello Doug,
> > > > You can put tubing together but travel might pet reduced.
> > > > Kabelschlepp and others sell cylindrical springs.
> > > > "Steel, Hilton" <HSteel@k...>
> > > > You might be able to make some out of very wide packing steel
> > band like
> > > > for
> > > > transport boxes. But I tell you ITS NASTY. I had to do
something
> > > > simmilar for
> > > > to substitute drill press springs. Therefor I prefer to buy
the
> > stuff.
> > > > Good luck
> > > > Sven Peter
> > > >
> > > > Doug Fortune wrote:
> > > > >
> > > > > dave_ace_me wrote:
> > > > >
> > > > > > btw, on my table, I am using a single lead screw, under
the
> > table,
> > > > > > with telescoping tubing as protection. This is very
simple
> > and well
> > > > > > worth the effort to keep chips clear.
> > > > >
> > > > > Hi Dave:
> > > > >
> > > > > I'd be interesting in hearing more about how you made those
> > > > > telescoping tubes. I think Reid sells nested sets of
aluminum
> > > > > tubes, but how do you get them to not pull completely apart?
> > > > >
> > > > > Doug Fortune
> > > > > http://www.cncKITS.com NEW -> 1KW power supply kits
> > > > >
> > > > > Addresses:
> > > > > FAQ: http://www.ktmarketing.com/faq.html
> > > > > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > > > >
> > > > > OFF Topic POSTS: General Machining
> > > > > If you wish to post on unlimited OT subjects goto:
> > > aol://5863:126/rec.crafts.metalworking or go thru Google.com to
> > reach it if
> > > you have trouble.
> > > > > http://www.metalworking.com/news_servers.html
> > > > >
> > > > > http://groups.yahoo.com/group/jobshophomeshop I consider
> this
> > as a
> > > sister site to the CCED group, as many of the same memembers
are
> > there, for
> > > OT subjects, that are not allowed on the CCED list.
> > > > >
> > > > > Post messages: CAD_CAM_EDM_DRO@y...
> > > > > Subscribe: CAD_CAM_EDM_DRO-subscribe@y...
> > > > > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@y...
> > > > > List owner: CAD_CAM_EDM_DRO-owner@y..., wanliker@a...
> > > > > Moderator: jmelson@a... timg@k... [Moderator]
> > > > > URL to this page:
> http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > > > > bill,
> > > > > List Mom
> > > > > List Owner
> > > > >
> > > > >
> > > > >
> > > > > Your use of Yahoo! Groups is subject to
> > > http://docs.yahoo.com/info/terms/
> > > >
> > > > Addresses:
> > > > FAQ: http://www.ktmarketing.com/faq.html
> > > > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > > >
> > > > OFF Topic POSTS: General Machining
> > > > If you wish to post on unlimited OT subjects goto:
> > > aol://5863:126/rec.crafts.metalworking or go thru Google.com to
> > reach it if
> > > you have trouble.
> > > > http://www.metalworking.com/news_servers.html
> > > >
> > > > http://groups.yahoo.com/group/jobshophomeshop I consider
this
> > as a
> > > sister site to the CCED group, as many of the same memembers
are
> > there, for
> > > OT subjects, that are not allowed on the CCED list.
> > > >
> > > >
> > > >
> > > > Post messages: CAD_CAM_EDM_DRO@y...
> > > > Subscribe: CAD_CAM_EDM_DRO-subscribe@y...
> > > > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@y...
> > > > List owner: CAD_CAM_EDM_DRO-owner@y..., wanliker@a...
> > > > Moderator: jmelson@a... timg@k... [Moderator]
> > > > URL to this page:
http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > > > bill,
> > > > List Mom
> > > > List Owner
> > > >
> > > >
> > > >
> > > > Your use of Yahoo! Groups is subject to
> > http://docs.yahoo.com/info/terms/
> > > >
> > > >
> > > >

Discussion Thread

Doug Fortune 2002-04-11 22:21:23 UTC telescoping leadscrew protectors dave_ace_me 2002-04-12 05:22:39 UTC Re: telescoping leadscrew protectors Sven Peter 2002-04-12 07:07:34 UTC Re: [CAD_CAM_EDM_DRO] telescoping leadscrew protectors Mike Snodgrass 2002-04-12 08:58:05 UTC Re: [CAD_CAM_EDM_DRO] telescoping leadscrew protectors rsgoldner 2002-04-12 09:33:33 UTC Re: telescoping leadscrew protectors dave_ace_me 2002-04-12 09:57:46 UTC leadscrew protectors ( was Re: telescoping leadscrew protectors Alan Marconett KM6VV 2002-04-12 10:33:09 UTC Re: [CAD_CAM_EDM_DRO] telescoping leadscrew protectors Mike Snodgrass 2002-04-12 10:47:31 UTC Re: [CAD_CAM_EDM_DRO] leadscrew protectors ( was Re: telescoping leadscrew protectors Jon Elson 2002-04-12 11:12:47 UTC Re: [CAD_CAM_EDM_DRO] telescoping leadscrew protectors Jon Elson 2002-04-12 11:15:03 UTC Re: [CAD_CAM_EDM_DRO] leadscrew protectors ( was Re: telescoping leadscrew protectors studleylee 2002-04-12 15:17:51 UTC leadscrew protectors ( was Re: telescoping leadscrew protectors Jerry Biehler 2002-04-12 16:51:05 UTC Re: [CAD_CAM_EDM_DRO] leadscrew protectors ( was Re: telescoping leadscrew protectors Brian Pitt 2002-04-12 20:23:02 UTC Re: [CAD_CAM_EDM_DRO] leadscrew protectors ( was Re: telescoping leadscrew protectors Brian Pitt 2002-04-12 20:37:35 UTC Re: [CAD_CAM_EDM_DRO] leadscrew protectors ( was Re: telescoping leadscrew protectors Paul Weber 2002-04-12 22:35:29 UTC Re: [CAD_CAM_EDM_DRO] telescoping leadscrew protectors Jon Elson 2002-04-12 22:35:55 UTC Re: [CAD_CAM_EDM_DRO] leadscrew protectors ( was Re: telescoping leadscrew protectors Tom Kahara 2002-04-13 12:38:30 UTC Re: [CAD_CAM_EDM_DRO] leadscrew protectors ( was Re: telescoping leadscrew protectors ballendo 2002-04-15 05:55:08 UTC leadscrew protectors ( was Re: telescoping leadscrew protectors ballendo 2002-04-15 06:27:35 UTC more leadscrew protectors ( was Re: telescoping leadscrew protectors Peter 2002-04-15 07:49:23 UTC Re: [CAD_CAM_EDM_DRO] more leadscrew protectors ( was Re: telescoping leadscrew protectors Alan Marconett KM6VV 2002-04-15 11:12:15 UTC Re: [CAD_CAM_EDM_DRO] more leadscrew protectors ( was Re: telescoping leadscrew protectors aspaguy 2002-04-15 21:17:28 UTC leadscrew protectors ( was Re: telescoping leadscrew protectors dave_ace_me 2002-04-16 13:48:33 UTC leadscrew protectors ( was Re: telescoping leadscrew protectors Jon Elson 2002-04-16 23:43:44 UTC Re: [CAD_CAM_EDM_DRO] leadscrew protectors ( was Re: telescoping leadscrew protectors ballendo 2002-04-17 02:19:48 UTC leadscrew protectors ( was Re: telescoping leadscrew protectors