Re: [CAD_CAM_EDM_DRO] low cost drivers
Posted by
Randy Gordon-Gilmore
on 2002-05-30 17:01:29 UTC
At 08:01 PM 5/30/2002 -0000, Richard wrote:
Sherline size 23 motors), which cost $150 and took a couple of lunch hours
to solder up.
Best regards,
Randy
Randy Gordon-Gilmore ,----.___________ ______________ _________________
ProtoTrains // = = === == || == == == = || == == == = == =|
Rio Vista, CA, USA /-O==O------------o==o------------o==o-----------o==o-'
zephyrus@... http://www.rickadee.net/~zephyrus
>What are some others experiences with the lower cost stepper drivers,I have very good use from the Camtronics 2A driver board kit (driving three
Sherline size 23 motors), which cost $150 and took a couple of lunch hours
to solder up.
Best regards,
Randy
Randy Gordon-Gilmore ,----.___________ ______________ _________________
ProtoTrains // = = === == || == == == = || == == == = == =|
Rio Vista, CA, USA /-O==O------------o==o------------o==o-----------o==o-'
zephyrus@... http://www.rickadee.net/~zephyrus
Discussion Thread
rekmac
2002-05-30 13:01:54 UTC
low cost drivers
JanRwl@A...
2002-05-30 16:40:38 UTC
Re: [CAD_CAM_EDM_DRO] low cost drivers
Randy Gordon-Gilmore
2002-05-30 17:01:29 UTC
Re: [CAD_CAM_EDM_DRO] low cost drivers
the_dutros
2002-05-30 22:38:04 UTC
Re: low cost drivers
Randy Gordon-Gilmore
2002-05-30 23:03:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: low cost drivers
alenz2002
2002-05-31 04:00:38 UTC
Re: low cost drivers
turbulatordude
2002-05-31 05:05:04 UTC
Re: low cost drivers
Carol & Jerry Jankura
2002-05-31 06:37:29 UTC
RE: [CAD_CAM_EDM_DRO] Re: low cost drivers
the_dutros
2002-05-31 07:08:17 UTC
Re: low cost drivers - reality
Mel Williams
2002-05-31 08:52:05 UTC
RE: [CAD_CAM_EDM_DRO] low cost drivers
rekmac
2002-05-31 12:10:19 UTC
Re: low cost drivers
mariss92705
2002-05-31 15:53:44 UTC
Cheap Power Supply was Re: low cost drivers
Les Watts
2002-05-31 16:14:34 UTC
Re: [CAD_CAM_EDM_DRO] Cheap Power Supply was Re: low cost drivers
JanRwl@A...
2002-05-31 17:18:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: low cost drivers
stevenson_engineers
2002-05-31 17:27:05 UTC
Re: low cost drivers
RC
2002-05-31 17:29:06 UTC
Re: [CAD_CAM_EDM_DRO] Cheap Power Supply was Re: low cost drivers
RC
2002-05-31 17:33:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: low cost drivers
mariss92705
2002-05-31 17:34:36 UTC
Cheap Power Supply was Re: low cost drivers
RC
2002-05-31 17:56:51 UTC
Re: [CAD_CAM_EDM_DRO] Cheap Power Supply was Re: low cost drivers
Les Watts
2002-05-31 18:26:28 UTC
Re: [CAD_CAM_EDM_DRO] Cheap Power Supply was Re: low cost drivers
JanRwl@A...
2002-05-31 18:46:09 UTC
Re: [CAD_CAM_EDM_DRO] Cheap Power Supply was Re: low cost drivers
stephen_stallings
2002-05-31 18:54:25 UTC
Cheap Power Supply was Re: low cost drivers
Tim Goldstein
2002-06-01 10:07:06 UTC
RE: [CAD_CAM_EDM_DRO] low cost drivers
RC
2002-06-01 13:15:48 UTC
Re: [CAD_CAM_EDM_DRO] Cheap Power Supply was Re: low cost drivers
JanRwl@A...
2002-06-01 20:04:04 UTC
Re: [CAD_CAM_EDM_DRO] Cheap Power Supply was Re: low cost drivers
StevenManzer
2002-06-26 02:04:22 UTC
Cheap Power Supply was Re: low cost drivers
Carlos Guillermo
2002-06-26 05:30:51 UTC
RE: [CAD_CAM_EDM_DRO] Cheap Power Supply was Re: low cost drivers
steveggca
2002-06-26 06:01:58 UTC
Cheap Power Supply was Re: low cost drivers
ballendo
2002-06-27 05:26:03 UTC
Cheap Power Supply was Re: low cost drivers