Posts by stephen_stallings

stephen_stallings 2001-12-21 20:05:06 UTC Re: followup to request for feedback, comments, and suggestions. stephen_stallings 2002-01-11 10:05:08 UTC Re: cad_cam_edm_dro archives update stephen_stallings 2002-02-17 19:01:38 UTC Re: Home Shop Machinist & Machinist's Workshop stephen_stallings 2002-02-20 21:35:01 UTC Re: DRO/plus software availability stephen_stallings 2002-02-21 21:16:28 UTC Getting the most out of this group, and finding alternatives stephen_stallings 2002-02-25 09:36:15 UTC Re: G-code---for the new millenium stephen_stallings 2002-02-26 10:24:38 UTC Re: Auto tool changers - preloading stephen_stallings 2002-02-28 10:15:27 UTC Re: Bridgeport Boss 8 RS-232 question stephen_stallings 2002-03-01 11:13:37 UTC Re: Gecko's don't like 7 x 10 (stepper resonance) stephen_stallings 2002-03-03 20:54:11 UTC Re: E.M.E. stephen_stallings 2002-03-17 21:41:29 UTC Re: 2002 NAMES reminder stephen_stallings 2002-03-22 09:48:33 UTC Re: NAMES and PRIME stephen_stallings 2002-03-27 09:18:11 UTC Re: steppers crosslinked? stephen_stallings 2002-03-27 11:36:06 UTC Re: question for potential Gecko 320/340 users - updated stephen_stallings 2002-03-28 12:05:30 UTC Re: Chopper circuit stephen_stallings 2002-03-29 01:55:19 UTC Re: stepper's crosslinked? stephen_stallings 2002-03-29 06:26:08 UTC Re: stepper's crosslinked? stephen_stallings 2002-04-06 19:35:01 UTC New product: break-out board with kitchen sink. stephen_stallings 2002-04-12 10:33:02 UTC Re: 8 wire steppers, parallel. series or single winding? stephen_stallings 2002-04-13 14:05:36 UTC PMDX-120 Parallel Port Accessory manual updated stephen_stallings 2002-04-16 22:20:51 UTC Re: Controlling more stepper drivers than I have outputs for? stephen_stallings 2002-04-17 19:14:35 UTC Re: Controlling more stepper drivers than I have outputs for? stephen_stallings 2002-04-24 21:10:28 UTC PMDX to show new stepper driver prototype at NAMES stephen_stallings 2002-04-30 11:03:05 UTC CNC exhibits at NAMES > photos posted stephen_stallings 2002-05-01 16:58:59 UTC Re: Stepper Drive Chips? - L7180 stephen_stallings 2002-05-04 14:37:29 UTC found source for small servos with encoders stephen_stallings 2002-05-07 20:20:07 UTC Re: NAMES Pictures stephen_stallings 2002-05-09 11:09:09 UTC Re: any software board combination that includes threading options? stephen_stallings 2002-05-14 08:14:21 UTC Re: Getting started - MaxNC comments stephen_stallings 2002-05-23 05:35:22 UTC Re: Anilam Crusader stephen_stallings 2002-05-24 19:07:38 UTC Re: Shielded cable connections - help stephen_stallings 2002-05-31 18:54:25 UTC Cheap Power Supply was Re: low cost drivers stephen_stallings 2002-06-01 06:37:32 UTC Re: EMC steps/rev calibration stephen_stallings 2002-06-06 07:39:51 UTC Re: A crazy idea stephen_stallings 2002-06-06 08:43:39 UTC Re: A crazy idea stephen_stallings 2002-06-09 06:21:33 UTC Re: Setting Gecko current stephen_stallings 2002-06-14 04:41:42 UTC Re: Wizdom required on circuit board milling. stephen_stallings 2002-07-09 09:33:22 UTC Re: Help implementing spindle & coolent on/off stephen_stallings 2002-07-10 08:45:27 UTC Re: Help implementing spindle & coolent on/off stephen_stallings 2002-08-06 22:10:35 UTC Re: More Parallel Port Woe's -- I think?