Re: EMC steps/rev calibration
Posted by
nahydro
on 2002-05-31 10:47:52 UTC
Alan:
Thanks for trying to help. Unfortunately, that is not the problem.
I've repeatedly checked the jumpers on the Geckos, and if the
documentation is correct, I believe I have them set correctly for x5
(second jumper position).
r
Thanks for trying to help. Unfortunately, that is not the problem.
I've repeatedly checked the jumpers on the Geckos, and if the
documentation is correct, I believe I have them set correctly for x5
(second jumper position).
r
--- In CAD_CAM_EDM_DRO@y..., Alan Marconett KM6VV <KM6VV@a...> wrote:
> Hi Nahydro,
>
> Perhaps you're actually setting x2 instead of x5 on the Gecko?
>
> Alan KM6VV
>
>
> nahydro wrote:
> >
> > I'm getting about half of the motor revs per inch of travel that I
> > want, and can't figure out why.
> >
> > My setup: EMC with 5 tpi screw, 1024 cpr encoder, and G340's in x5
> > mode.
> >
> > I have INPUT_SCALE = 1024 0 and OUTPUT_SCALE = 1 0.
> >
> > When I jog 1 inch (any axis) I get about 2.5 motor shaft
rotations. I
> > expect 5.
> >
> > Any ideas? TIA
> >
> > r
Discussion Thread
nahydro
2002-05-31 02:15:31 UTC
EMC steps/rev calibration
Alan Marconett KM6VV
2002-05-31 10:35:09 UTC
Re: [CAD_CAM_EDM_DRO] EMC steps/rev calibration
nahydro
2002-05-31 10:47:52 UTC
Re: EMC steps/rev calibration
andyolney
2002-05-31 12:08:06 UTC
Re: EMC steps/rev calibration
Alan Marconett KM6VV
2002-05-31 12:41:46 UTC
Re: EMC steps/rev calibration
nahydro
2002-06-01 00:14:18 UTC
Re: EMC steps/rev calibration
stephen_stallings
2002-06-01 06:37:32 UTC
Re: EMC steps/rev calibration
Dan Mauch
2002-06-01 06:44:15 UTC
RE: [CAD_CAM_EDM_DRO] Re: EMC steps/rev calibration
Ray Henry
2002-06-01 08:02:37 UTC
Re: Re: EMC steps/rev calibration
Tim Goldstein
2002-06-01 10:32:44 UTC
RE: [CAD_CAM_EDM_DRO] EMC steps/rev calibration
nahydro
2002-06-01 11:35:06 UTC
Re: EMC steps/rev calibration
nahydro
2002-06-01 11:40:54 UTC
Re: EMC steps/rev calibration
Alan Marconett KM6VV
2002-06-01 12:11:10 UTC
Re: EMC steps/rev calibration
Ray Henry
2002-06-01 12:55:07 UTC
Re: Re: EMC steps/rev calibration
nahydro
2002-06-03 11:01:25 UTC
EMC steps/rev calibration-SOLVED
studleylee
2002-06-03 16:05:24 UTC
Re: EMC steps/rev calibration-SOLVED
nahydro
2002-06-03 17:23:10 UTC
Re: EMC steps/rev calibration-SOLVED
Ray Henry
2002-06-04 07:44:06 UTC
Re: Re: EMC steps/rev calibration-SOLVED
nahydro
2002-06-04 17:39:39 UTC
Re: EMC steps/rev calibration-SOLVED
William Scalione
2002-06-04 22:19:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: EMC steps/rev calibration-SOLVED