Re: [CAD_CAM_EDM_DRO] Re: loosing steps
Posted by
Jon Elson
on 2002-07-30 22:50:09 UTC
Gene wrote:
I used to think it would be 4x worse, but Mariss corrected me on that.
But, the torque will fall off twice as fast with speed in series. Holding
torque will be minutely higher in series.
Jon
> What could I expect if I ran it in series at half the amps?Throughout most of the speed range, performance will be worse.
I used to think it would be 4x worse, but Mariss corrected me on that.
But, the torque will fall off twice as fast with speed in series. Holding
torque will be minutely higher in series.
Jon
Discussion Thread
Gene
2002-07-27 19:39:00 UTC
loosing steps
mariss92705
2002-07-27 19:56:04 UTC
Re: loosing steps
Gene
2002-07-27 20:14:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: loosing steps
Jon Elson
2002-07-27 22:04:02 UTC
Re: [CAD_CAM_EDM_DRO] loosing steps
Jon Elson
2002-07-27 22:06:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: loosing steps
Gene
2002-07-27 22:21:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: loosing steps
studleylee
2002-07-28 14:22:29 UTC
Re: loosing steps & max stepper voltage >30x??.
Jon Elson
2002-07-28 22:26:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: loosing steps
Gene
2002-07-28 23:51:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: loosing steps
mariss92705
2002-07-29 08:28:14 UTC
Re: loosing steps
mariss92705
2002-07-29 08:51:37 UTC
Re: loosing steps
Gene
2002-07-29 10:23:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: loosing steps
mariss92705
2002-07-29 10:47:09 UTC
Re: loosing steps
Gene
2002-07-29 12:34:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: loosing steps
Jon Elson
2002-07-29 22:31:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: loosing steps
Jon Elson
2002-07-29 22:34:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: loosing steps
Gene
2002-07-30 15:51:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: loosing steps
Jon Elson
2002-07-30 20:06:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: loosing steps
Gene
2002-07-30 20:30:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: loosing steps
Gene
2002-07-30 20:32:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: loosing steps
studleylee
2002-07-30 21:14:42 UTC
Re: loosing steps
Jon Elson
2002-07-30 22:50:09 UTC
Re: [CAD_CAM_EDM_DRO] Re: loosing steps
studleylee
2002-08-01 13:01:51 UTC
Re: loosing steps...
Gene
2002-08-01 13:27:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: loosing steps...