Re: loosing steps...
Posted by
studleylee
on 2002-08-01 13:01:51 UTC
Gene,
Did you get any further on this testing?
Thanks,
-Lee
Did you get any further on this testing?
Thanks,
-Lee
--- In CAD_CAM_EDM_DRO@y..., Gene <capper@i...> wrote:
> What could I expect if I ran it in series at half the amps?
>
> Jon Elson wrote:
> >
> > Gene wrote:
> >
> > > Here's what I found out.
> > > The Oriental Motor specifications are:
> > >
> > > Holding Torque: 305 oz-in(for Unipolar), 430 oz-in(for Bipolar)
at full
> > > step
>
Discussion Thread
Gene
2002-07-27 19:39:00 UTC
loosing steps
mariss92705
2002-07-27 19:56:04 UTC
Re: loosing steps
Gene
2002-07-27 20:14:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: loosing steps
Jon Elson
2002-07-27 22:04:02 UTC
Re: [CAD_CAM_EDM_DRO] loosing steps
Jon Elson
2002-07-27 22:06:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: loosing steps
Gene
2002-07-27 22:21:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: loosing steps
studleylee
2002-07-28 14:22:29 UTC
Re: loosing steps & max stepper voltage >30x??.
Jon Elson
2002-07-28 22:26:52 UTC
Re: [CAD_CAM_EDM_DRO] Re: loosing steps
Gene
2002-07-28 23:51:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: loosing steps
mariss92705
2002-07-29 08:28:14 UTC
Re: loosing steps
mariss92705
2002-07-29 08:51:37 UTC
Re: loosing steps
Gene
2002-07-29 10:23:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: loosing steps
mariss92705
2002-07-29 10:47:09 UTC
Re: loosing steps
Gene
2002-07-29 12:34:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: loosing steps
Jon Elson
2002-07-29 22:31:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: loosing steps
Jon Elson
2002-07-29 22:34:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: loosing steps
Gene
2002-07-30 15:51:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: loosing steps
Jon Elson
2002-07-30 20:06:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: loosing steps
Gene
2002-07-30 20:30:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: loosing steps
Gene
2002-07-30 20:32:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: loosing steps
studleylee
2002-07-30 21:14:42 UTC
Re: loosing steps
Jon Elson
2002-07-30 22:50:09 UTC
Re: [CAD_CAM_EDM_DRO] Re: loosing steps
studleylee
2002-08-01 13:01:51 UTC
Re: loosing steps...
Gene
2002-08-01 13:27:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: loosing steps...