Re: EDM troubles - update
Posted by
turbulatordude
on 2003-08-24 14:33:25 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "tomp_tag" <tomp_tag@i...>
wrote:
siphon off the top 3/4 into a second, and as it drains, run it thru a
simple filter.
low tech, but the water ohms out pretty low. less than 200k ohms
with my fingers holding the tips about this (holds fingers up) far
apart.
same distance and tap water ohms out to over 600k
Dave
wrote:
> floculent?slow
> We built settling pans for wire edms, usings nested pans where the
> moving water had tosettle out
> exit one pan by flowing over its edge into the next. Particulates
> rather than go overgiven enuf
> the edge when the flow is slow. So, a baffle will do the trick ,
> baffles, slow enufbetter than
> velocity but high enuf volume makes a simple solution. Worked
> specializedI'm doing the simple twin 5 gal bucket trick. let one fill, then
> sub-micron filters!
> tomp
siphon off the top 3/4 into a second, and as it drains, run it thru a
simple filter.
low tech, but the water ohms out pretty low. less than 200k ohms
with my fingers holding the tips about this (holds fingers up) far
apart.
same distance and tap water ohms out to over 600k
Dave
Discussion Thread
turbulatordude
2003-08-10 16:29:00 UTC
EDM troubles
Zafar Salam
2003-08-10 21:14:40 UTC
Re: [CAD_CAM_EDM_DRO] EDM troubles
tomp_tag
2003-08-10 21:44:34 UTC
Re: [CAD_CAM_EDM_DRO] EDM troubles
Jon Elson
2003-08-10 23:08:33 UTC
Re: [CAD_CAM_EDM_DRO] EDM troubles
turbulatordude
2003-08-11 06:58:31 UTC
Re: EDM troubles
Jon Elson
2003-08-11 09:41:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: EDM troubles
Andrew Mawson
2003-08-11 09:57:06 UTC
Re: EDM troubles
turbulatordude
2003-08-11 12:28:37 UTC
Re: EDM troubles
turbulatordude
2003-08-11 12:48:26 UTC
Re: EDM troubles
Richard
2003-08-11 16:39:52 UTC
Re: EDM troubles
turbulatordude
2003-08-11 19:50:11 UTC
Re: EDM troubles
tomp_tag
2003-08-11 22:39:50 UTC
Re: [CAD_CAM_EDM_DRO] Re: EDM troubles
turbulatordude
2003-08-23 05:22:50 UTC
Re: EDM troubles - update
tomp_tag
2003-08-23 23:19:26 UTC
Re: [CAD_CAM_EDM_DRO] Re: EDM troubles - update
turbulatordude
2003-08-24 07:23:09 UTC
Re: EDM troubles - update
Richard
2003-08-24 08:26:26 UTC
Re: EDM troubles - update
tomp_tag
2003-08-24 11:37:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: EDM troubles - update
turbulatordude
2003-08-24 14:26:59 UTC
Re: EDM troubles - update
turbulatordude
2003-08-24 14:33:25 UTC
Re: EDM troubles - update