Re: Servo only moving one way

1) Remove the wire going to the G320 DIRECTION terminal.
2) Connect a test wire to GROUND on your breakout board.
3) Jog the G320.
4) While jogging, touch the test wire to the G320 DIRECTION term.

The drive must reverse direction then. If it does not, return it to
us for evaluation and/or repair.

Mariss

--- In CAD_CAM_EDM_DRO@yahoogroups.com, <james_cullins@s...> wrote:
> Ok , now does the output change form 5v to 0v when you jog back and
forth?
> If it does then is something after the breakout board. Maybe the
opto in the
> Gecko is not responding .
> If doe not change let me know.
> Jim
>
>
> ----- Original Message -----
> From: "INDECO" <indeco@i...>
> To: <CAD_CAM_EDM_DRO@yahoogroups.com>
> Sent: Thursday, March 11, 2004 3:24 PM
> Subject: Re: [CAD_CAM_EDM_DRO] Servo only moving one way
>
>
> > Sorry Jim,
> > I was reading the wrong line on the meter.
> > Your right it doesn't go any higher than 5v.
> >
> > I have double and triple check the wires...they are correct.
> >
> > Robin
> >
> >
> >
> > ----- Original Message -----
> > From: <james_cullins@s...>
> > To: <CAD_CAM_EDM_DRO@yahoogroups.com>
> > Sent: Thursday, March 11, 2004 3:48 PM
> > Subject: Re: [CAD_CAM_EDM_DRO] Servo only moving one way
> >
> >
> > > Are you looking on the breakout board?
> > > Are you grounding to the PCgnd by the parallel port connector?
> > > do not connect the PCgnd to anything .
> > > You should never read over 5v.
> > > I would double check the wiring.
> > > Jim
> > > ----- Original Message -----
> > > From: "INDECO" <indeco@i...>
> > > To: <CAD_CAM_EDM_DRO@yahoogroups.com>
> > > Sent: Thursday, March 11, 2004 2:34 PM
> > > Subject: Re: [CAD_CAM_EDM_DRO] Servo only moving one way
> > >
> > >
> > > > Jim,
> > > >
> > > > It goes from 5v to 30v never reaches 0v always carring at
least 5v.
> > > > When I jog (in Y axis) right the DIR light comes on and it
reads 30v
> > then
> > > > when I jog left, the light goes out and it reads 5v.
> > > > As for the X axis it will only move one way with both key
strokes.
> > > > What is 74hct541? Is it something I can fix...or will I have
to have a
> > new
> > > > board.
> > > >
> > > >
> > > > Robin
> > > >
> > > >
> > > >
> > > > ----- Original Message -----
> > > > From: <james_cullins@s...>
> > > > To: <CAD_CAM_EDM_DRO@yahoogroups.com>
> > > > Sent: Thursday, March 11, 2004 2:55 PM
> > > > Subject: Re: [CAD_CAM_EDM_DRO] Servo only moving one way
> > > >
> > > >
> > > > > Robin if you have just a common volt ohm meter like a
Radio Shack
> you
> > > can
> > > > > test it.
> > > > > Just read the voltage on the screw terminal for the Y axis
Dir . It
> > > should
> > > > > change form a 0 to 5v when you jog it.
> > > > > If it doesn't and the LED is changing the 74hct541 is
probably bad.
> > > > > Let us know and we will make it right for you.
> > > > > Jim
> > > > > ----- Original Message -----
> > > > > From: "INDECO" <indeco@i...>
> > > > > To: <CAD_CAM_EDM_DRO@yahoogroups.com>
> > > > > Sent: Thursday, March 11, 2004 11:55 AM
> > > > > Subject: Re: [CAD_CAM_EDM_DRO] Servo only moving one way
> > > > >
> > > > >
> > > > > > Yes I am using Gecko drives with Bob Campbells
Breakout board
> and
> > > > Mach
> > > > > 2
> > > > > > software.
> > > > > > I have niether a logic probe or a oscilloscope to check
it.
> > > > > > However the direction light on the board is not lit up as
the Y
> axis
> > > is,
> > > > > > however the light on the Y only lights when I jog to the
left then
> > > goes
> > > > > out
> > > > > > when I jog right. Is this right?
> > > > > > The drivers do not fault, it just will not jog both
ways in the
> X
> > > > > > axis...both key strokes go same way.
> > > > > > The Y axis seems to be ok. I have checked and double
check the
> wires
> > > and
> > > > > > they are correct.
> > > > > > Could it be in Mach2 that I'm doing something wrong?
> > > > > >
> > > > > >
> > > > > > Thanks, Robin
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > > ----- Original Message -----
> > > > > > From: "Jon Elson" <elson@p...>
> > > > > > To: <CAD_CAM_EDM_DRO@yahoogroups.com>
> > > > > > Sent: Thursday, March 11, 2004 12:24 PM
> > > > > > Subject: Re: [CAD_CAM_EDM_DRO] Servo only moving one way
> > > > > >
> > > > > >
> > > > > > >
> > > > > > >
> > > > > > > INDECO wrote:
> > > > > > >
> > > > > > > >Hello all,
> > > > > > > >
> > > > > > > > I am having a little trouble figuring this one
out...my X
> axis
> > > will
> > > > > > only move one way.
> > > > > > > >When I jog the X axis both key strokes move it the
same way.
> > > > > > > >Help if you can.
> > > > > > > >
> > > > > > > >
> > > > > > > What type of drive are you using? I have to assume a
Gecko
> > 320/340,
> > > > > since
> > > > > > > you don't say. What software are you using? Does the
Y axis
> work
> > > > > right?
> > > > > > >
> > > > > > > The Gecko has a direction signal which determines which
way it
> is
> > to
> > > > > move.
> > > > > > > It sounds like the step pulse is getting through fine,
but the
> > > > direction
> > > > > > > is not.
> > > > > > >
> > > > > > > Check your wiring, use a DVM, logic probe or
oscilloscope to
> check
> > > the
> > > > > > > direction
> > > > > > > signal to see if it is changing. Geckos need a fair
bit of opto
> > > > current
> > > > > > > to operate,
> > > > > > > somewhere in the 10 - 15 mA range.
> > > > > > >
> > > > > > > Jon
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > > Addresses:
> > > > > > > FAQ: http://www.ktmarketing.com/faq.html
> > > > > > > FILES:
http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > > > > > > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> > > > > > >
> > > > > > > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > > > > > > Unsubscribe: CAD_CAM_EDM_DRO-
unsubscribe@yahoogroups.com
> > > > > > > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
> > > wanliker@a...,
> > > > > > timg@k...
> > > > > > > Moderator: pentam@c... indigo_red@q...
> > > davemucha@j...
> > > > > > [Moderators]
> > > > > > > URL to this group:
http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > > > > > >
> > > > > > > OFF Topic POSTS: General Machining
> > > > > > > If you wish to post on unlimited OT subjects goto:
> > > > > > aol://5863:126/rec.crafts.metalworking or go thru
Google.com to
> > reach
> > > it
> > > > > if
> > > > > > you have trouble.
> > > > > > > http://www.metalworking.com/news_servers.html
> > > > > > >
> > > > > > > http://groups.yahoo.com/group/jobshophomeshop I
consider this
> to
> > > be
> > > > a
> > > > > > sister site to the CCED group, as many of the same
members are
> > there,
> > > > for
> > > > > OT
> > > > > > subjects, that are not allowed on the CCED list.
> > > > > > >
> > > > > > > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN
BY
> POSTING
> > > > THEM.
> > > > > > DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO
EXCEPTIONS........
> > > > > > > bill
> > > > > > > List Mom
> > > > > > > List Owner
> > > > > > >
> > > > > > >
> > > > > > > Yahoo! Groups Links
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > > Addresses:
> > > > > > FAQ: http://www.ktmarketing.com/faq.html
> > > > > > FILES:
http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > > > > > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> > > > > >
> > > > > > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > > > > > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > > > > > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
> > wanliker@a...,
> > > > > timg@k...
> > > > > > Moderator: pentam@c... indigo_red@q...
> > davemucha@j...
> > > > > [Moderators]
> > > > > > URL to this group:
http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > > > > >
> > > > > > OFF Topic POSTS: General Machining
> > > > > > If you wish to post on unlimited OT subjects goto:
> > > > > aol://5863:126/rec.crafts.metalworking or go thru
Google.com to
> reach
> > it
> > > > if
> > > > > you have trouble.
> > > > > > http://www.metalworking.com/news_servers.html
> > > > > >
> > > > > > http://groups.yahoo.com/group/jobshophomeshop I
consider this to
> > be
> > > a
> > > > > sister site to the CCED group, as many of the same members
are
> there,
> > > for
> > > > OT
> > > > > subjects, that are not allowed on the CCED list.
> > > > > >
> > > > > > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN
BY POSTING
> > > THEM.
> > > > > DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO
EXCEPTIONS........
> > > > > > bill
> > > > > > List Mom
> > > > > > List Owner
> > > > > >
> > > > > >
> > > > > > Yahoo! Groups Links
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > > Addresses:
> > > > > FAQ: http://www.ktmarketing.com/faq.html
> > > > > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > > > > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> > > > >
> > > > > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > > > > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > > > > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
> wanliker@a...,
> > > > timg@k...
> > > > > Moderator: pentam@c... indigo_red@q...
> davemucha@j...
> > > > [Moderators]
> > > > > URL to this group:
http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > > > >
> > > > > OFF Topic POSTS: General Machining
> > > > > If you wish to post on unlimited OT subjects goto:
> > > > aol://5863:126/rec.crafts.metalworking or go thru Google.com
to reach
> it
> > > if
> > > > you have trouble.
> > > > > http://www.metalworking.com/news_servers.html
> > > > >
> > > > > http://groups.yahoo.com/group/jobshophomeshop I consider
this to
> be
> > a
> > > > sister site to the CCED group, as many of the same members
are there,
> > for
> > > OT
> > > > subjects, that are not allowed on the CCED list.
> > > > >
> > > > > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY
POSTING
> > THEM.
> > > > DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO
EXCEPTIONS........
> > > > > bill
> > > > > List Mom
> > > > > List Owner
> > > > >
> > > > >
> > > > > Yahoo! Groups Links
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > >
> > > >
> > > >
> > > >
> > > > Addresses:
> > > > FAQ: http://www.ktmarketing.com/faq.html
> > > > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > > > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> > > >
> > > > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > > > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > > > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
wanliker@a...,
> > > timg@k...
> > > > Moderator: pentam@c... indigo_red@q... davemucha@j...
> > > [Moderators]
> > > > URL to this group:
http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > > >
> > > > OFF Topic POSTS: General Machining
> > > > If you wish to post on unlimited OT subjects goto:
> > > aol://5863:126/rec.crafts.metalworking or go thru Google.com to
reach it
> > if
> > > you have trouble.
> > > > http://www.metalworking.com/news_servers.html
> > > >
> > > > http://groups.yahoo.com/group/jobshophomeshop I consider
this to be
> a
> > > sister site to the CCED group, as many of the same members are
there,
> for
> > OT
> > > subjects, that are not allowed on the CCED list.
> > > >
> > > > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY
POSTING
> THEM.
> > > DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> > > > bill
> > > > List Mom
> > > > List Owner
> > > >
> > > >
> > > > Yahoo! Groups Links
> > > >
> > > >
> > > >
> > > >
> > >
> > >
> > >
> > >
> > > Addresses:
> > > FAQ: http://www.ktmarketing.com/faq.html
> > > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> > >
> > > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
wanliker@a...,
> > timg@k...
> > > Moderator: pentam@c... indigo_red@q... davemucha@j...
> > [Moderators]
> > > URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> > >
> > > OFF Topic POSTS: General Machining
> > > If you wish to post on unlimited OT subjects goto:
> > aol://5863:126/rec.crafts.metalworking or go thru Google.com to
reach it
> if
> > you have trouble.
> > > http://www.metalworking.com/news_servers.html
> > >
> > > http://groups.yahoo.com/group/jobshophomeshop I consider this
to be a
> > sister site to the CCED group, as many of the same members are
there, for
> OT
> > subjects, that are not allowed on the CCED list.
> > >
> > > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY
POSTING THEM.
> > DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> > > bill
> > > List Mom
> > > List Owner
> > >
> > >
> > > Yahoo! Groups Links
> > >
> > >
> > >
> > >
> > >
> >
> >
> >
> >
> > Addresses:
> > FAQ: http://www.ktmarketing.com/faq.html
> > FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> > Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
> >
> > Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> > Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> > List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
wanliker@a...,
> timg@k...
> > Moderator: pentam@c... indigo_red@q... davemucha@j...
> [Moderators]
> > URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> >
> > OFF Topic POSTS: General Machining
> > If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to
reach it if
> you have trouble.
> > http://www.metalworking.com/news_servers.html
> >
> > http://groups.yahoo.com/group/jobshophomeshop I consider this
to be a
> sister site to the CCED group, as many of the same members are
there, for OT
> subjects, that are not allowed on the CCED list.
> >
> > NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY
POSTING THEM.
> DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> > bill
> > List Mom
> > List Owner
> >
> >
> > Yahoo! Groups Links
> >
> >
> >
> >