Re: Servo only moving one way
Posted by
jmkasunich
on 2004-03-12 10:48:02 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, Jon Elson <elson@p...> wrote:
put the LEDs in parallel - that way you can see the state of
the outputs regardless of the drive design, or even if the
drive is disconnected.
To make the right troubleshooting decision, he needs to know
a little about his breakout board. He could disconnect the Y
drive and see if the Y light still works. If so, then the
dark X light points to the computer or port or cable, etc.
If not, then as you say, the drive or its connections could
also be at fault.
John Kasunich
>Good point. Although if I were designing a breakout board I'd
> > in fact he
> >says "the direction light on the board is not lit up as the
> >Y axis is", so that implies that the X light is _not_ working.
> >He previously stated that the problem axis is X, so the dark
> >LED points to a computer/parport/cable issue, NOT a drive
> >issue.
> >
> >
> Maybe. If the X LED is in SERIES with the LED in the driver's
> optocoupler, then a problem with wiring or the driver could
> cause the LED on the breakout board to not work.
put the LEDs in parallel - that way you can see the state of
the outputs regardless of the drive design, or even if the
drive is disconnected.
To make the right troubleshooting decision, he needs to know
a little about his breakout board. He could disconnect the Y
drive and see if the Y light still works. If so, then the
dark X light points to the computer or port or cable, etc.
If not, then as you say, the drive or its connections could
also be at fault.
John Kasunich
Discussion Thread
INDECO
2004-03-11 06:29:21 UTC
Servo only moving one way
John Johnson
2004-03-11 06:52:29 UTC
Re: [CAD_CAM_EDM_DRO] Servo only moving one way
Harvey White
2004-03-11 09:19:32 UTC
Re: [CAD_CAM_EDM_DRO] Servo only moving one way
Jon Elson
2004-03-11 09:23:12 UTC
Re: [CAD_CAM_EDM_DRO] Servo only moving one way
Brian
2004-03-11 09:32:17 UTC
Re: [CAD_CAM_EDM_DRO] Servo only moving one way
INDECO
2004-03-11 09:55:46 UTC
Re: [CAD_CAM_EDM_DRO] Servo only moving one way
Ed Gilbert
2004-03-11 10:11:48 UTC
RE: [CAD_CAM_EDM_DRO] Servo only moving one way
alex
2004-03-11 10:25:21 UTC
Re: [CAD_CAM_EDM_DRO] USB of Jon Elson
INDECO
2004-03-11 10:35:27 UTC
Re: [CAD_CAM_EDM_DRO] Servo only moving one way
Dan Mauch
2004-03-11 11:10:31 UTC
Re: [CAD_CAM_EDM_DRO] Servo only moving one way
james_cullins@s...
2004-03-11 12:03:46 UTC
Re: [CAD_CAM_EDM_DRO] Servo only moving one way
INDECO
2004-03-11 12:35:08 UTC
Re: [CAD_CAM_EDM_DRO] Servo only moving one way
james_cullins@s...
2004-03-11 12:52:32 UTC
Re: [CAD_CAM_EDM_DRO] Servo only moving one way
INDECO
2004-03-11 13:24:05 UTC
Re: [CAD_CAM_EDM_DRO] Servo only moving one way
james_cullins@s...
2004-03-11 14:58:29 UTC
Re: [CAD_CAM_EDM_DRO] Servo only moving one way
Mariss Freimanis
2004-03-11 17:19:12 UTC
Re: Servo only moving one way
Jon Elson
2004-03-11 19:18:17 UTC
Re: [CAD_CAM_EDM_DRO] Servo only moving one way
Jon Elson
2004-03-11 19:38:22 UTC
Re: [CAD_CAM_EDM_DRO] USB of Jon Elson
jmkasunich
2004-03-12 06:26:27 UTC
Re: Servo only moving one way
alex
2004-03-12 06:59:57 UTC
Re: [CAD_CAM_EDM_DRO] USB of Jon Elson
Jon Elson
2004-03-12 10:30:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo only moving one way
Jon Elson
2004-03-12 10:37:44 UTC
Re: [CAD_CAM_EDM_DRO] USB of Jon Elson
jmkasunich
2004-03-12 10:48:02 UTC
Re: Servo only moving one way
alex
2004-03-12 11:39:13 UTC
Re: [CAD_CAM_EDM_DRO] USB of Jon Elson
james_cullins@s...
2004-03-12 12:59:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo only moving one way
Mariss Freimanis
2004-03-12 13:14:02 UTC
Re: Servo only moving one way
INDECO
2004-03-12 14:28:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo only moving one way
james_cullins@s...
2004-03-12 14:33:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo only moving one way
james_cullins@s...
2004-03-12 14:40:41 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo only moving one way
james_cullins@s...
2004-03-12 14:41:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo only moving one way
Mariss Freimanis
2004-03-12 15:15:08 UTC
Re: Servo only moving one way
james_cullins@s...
2004-03-12 20:45:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo only moving one way
Jon Elson
2004-03-12 20:55:57 UTC
Re: [CAD_CAM_EDM_DRO] USB of Jon Elson
INDECO
2004-03-13 06:18:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo only moving one way
james_cullins@s...
2004-03-13 06:46:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo only moving one way
alex
2004-03-13 13:20:06 UTC
Re: [CAD_CAM_EDM_DRO] USB of Jon Elson