Re: wiring Gecko drivers - power
Posted by
turbulatordude
on 2004-08-16 23:45:12 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "theokspindoctor" <mail@t...>
wrote:
The power delivered is the key. if your motors are undersized or the
friction is high, your motors will skip steps.
if your resistor is wrong, you will over or under power the motors
and skip steps.
if your ramp speed is too high, you will skip steps.
the 'cry' noise is your skipped steps. the good thing is that all
that gets harmed is your nerves.
Read Mariss's white paper while you are waiting for your replacement
Gecko. That should clear up your confusion.
Then re-read the Gecko conection guide. That too should clear up any
remainning questions.
Dave
wrote:
> Another question. The 201 Gecko puts out 2000 steps perwill
> revolution. My motors are maxing out at 20 inches per minute with
> 6000 pulses per second. Anything higher stalls the motor and it
> only cry with no movement. Either they are wired wrong or theof
> motors can not handle the high pusle rate. Would I be better off
> with the Gecko 210. It seems from the Gecko website that instead
> fewer pulses the 210 can put up to 10 times more ( up to 20000steps
> per revolution), so that will not solve my problem. Am I correctin
> this assumption? or is it that it can go down to 200 steps per revNO.
> which would be better for me.
>
> thanks
> Keith Clark
The power delivered is the key. if your motors are undersized or the
friction is high, your motors will skip steps.
if your resistor is wrong, you will over or under power the motors
and skip steps.
if your ramp speed is too high, you will skip steps.
the 'cry' noise is your skipped steps. the good thing is that all
that gets harmed is your nerves.
Read Mariss's white paper while you are waiting for your replacement
Gecko. That should clear up your confusion.
Then re-read the Gecko conection guide. That too should clear up any
remainning questions.
Dave
Discussion Thread
theokspindoctor
2004-08-16 20:05:47 UTC
wiring Gecko drivers
Robert Williams
2004-08-16 20:48:22 UTC
Re: [CAD_CAM_EDM_DRO] wiring Gecko drivers
theokspindoctor
2004-08-16 21:00:04 UTC
Re: wiring Gecko drivers
theokspindoctor
2004-08-16 21:12:13 UTC
Re: wiring Gecko drivers
Robert Williams
2004-08-16 21:23:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers
JanRwl@A...
2004-08-16 21:32:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers
theokspindoctor
2004-08-16 21:44:31 UTC
Re: wiring Gecko drivers
Jon Elson
2004-08-16 21:46:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers
theokspindoctor
2004-08-16 21:49:37 UTC
Re: wiring Gecko drivers
theokspindoctor
2004-08-16 22:15:40 UTC
Re: burning Gecko drive
turbulatordude
2004-08-16 23:39:07 UTC
Re: burning Gecko drive
turbulatordude
2004-08-16 23:45:12 UTC
Re: wiring Gecko drivers - power
turbulatordude
2004-08-16 23:50:40 UTC
Re: wiring Gecko drivers - light bulb
turbulatordude
2004-08-16 23:52:12 UTC
Re: wiring Gecko drivers - Bullet Proof Geckos ?
Les Newell
2004-08-17 01:57:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: burning Gecko drive
theokspindoctor
2004-08-17 05:23:37 UTC
Re: burning Gecko drive
Robert Williams
2004-08-17 06:25:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: burning Gecko drive
Robert Williams
2004-08-17 07:03:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers
Dan Mauch
2004-08-17 07:31:39 UTC
Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers - Bullet Proof Geckos ?
Jon Elson
2004-08-17 10:15:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers
Jon Elson
2004-08-17 10:18:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers
Jon Elson
2004-08-17 10:24:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: burning Gecko drive
Jon Elson
2004-08-17 10:33:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: burning Gecko drive
Les Newell
2004-08-17 11:33:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: burning Gecko drive
vavaroutsos
2004-08-17 11:34:08 UTC
Re: burning Gecko drive
turbulatordude
2004-08-17 13:42:29 UTC
Re: wiring Gecko drivers - possibley bad steps
JanRwl@A...
2004-08-17 14:12:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers
Stephen Wille Padnos
2004-08-17 14:18:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers
theokspindoctor
2004-08-17 18:07:17 UTC
Re: wiring Gecko drivers
Jon Elson
2004-08-17 18:42:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: burning Gecko drive
JanRwl@A...
2004-08-17 20:50:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers
theokspindoctor
2004-08-17 22:50:57 UTC
Re: wiring Gecko drivers
Les Newell
2004-08-18 01:22:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers