CAD CAM EDM DRO - Yahoo Group Archive

Re: wiring Gecko drivers - possibley bad steps

on 2004-08-17 13:42:29 UTC
>
> > Am I correct in
> >this assumption? or is it that it can go down to 200 steps per rev
> >which would be better for me.
> >
> >
> Yes, it can, but I really don't think this is going to fix your
problem.
>
> One thing I would do is connect a set of headphones, with perhaps a
1000 Ohm
> series resistor between the Gecko's +5 VDC and STEP terminals.
Then, listen
> to the tone as you jog the machine into the speed range where it
has a
> problem.
> Does the tone rise and fall like slide whistle (ie. a very clean
tone)
> or like a bunch
> of angry bees (a raspy, buzzing noise with little tone to be
heard)? If
> the former,
> it has to be the motors (unless it is due to the lack of capacitors
or
> the improper
> adjustment of the midband resonance damping). I'm having a problem
> understanding
> why it is crapping out at only 6666 microsteps/second. But, if you
hear
> the buzzing
> noise instead of the clean tone, then your step pulse train is not
> "smooth", ie. the
> timing between step pulses is varying greatly, and this will cause
the
> step motors
> to lose sync.


Would it be funny if he was running something like Turbo-CNC in a DOS
window and just not getting any ramping as Windoz phases in and out ?

Neat trick with the headphones.

I just listen to AM and the soothing whine and whistles from the
noise is enough for me.

Dave

Discussion Thread

theokspindoctor 2004-08-16 20:05:47 UTC wiring Gecko drivers Robert Williams 2004-08-16 20:48:22 UTC Re: [CAD_CAM_EDM_DRO] wiring Gecko drivers theokspindoctor 2004-08-16 21:00:04 UTC Re: wiring Gecko drivers theokspindoctor 2004-08-16 21:12:13 UTC Re: wiring Gecko drivers Robert Williams 2004-08-16 21:23:03 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers JanRwl@A... 2004-08-16 21:32:19 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers theokspindoctor 2004-08-16 21:44:31 UTC Re: wiring Gecko drivers Jon Elson 2004-08-16 21:46:03 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers theokspindoctor 2004-08-16 21:49:37 UTC Re: wiring Gecko drivers theokspindoctor 2004-08-16 22:15:40 UTC Re: burning Gecko drive turbulatordude 2004-08-16 23:39:07 UTC Re: burning Gecko drive turbulatordude 2004-08-16 23:45:12 UTC Re: wiring Gecko drivers - power turbulatordude 2004-08-16 23:50:40 UTC Re: wiring Gecko drivers - light bulb turbulatordude 2004-08-16 23:52:12 UTC Re: wiring Gecko drivers - Bullet Proof Geckos ? Les Newell 2004-08-17 01:57:46 UTC Re: [CAD_CAM_EDM_DRO] Re: burning Gecko drive theokspindoctor 2004-08-17 05:23:37 UTC Re: burning Gecko drive Robert Williams 2004-08-17 06:25:13 UTC Re: [CAD_CAM_EDM_DRO] Re: burning Gecko drive Robert Williams 2004-08-17 07:03:33 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers Dan Mauch 2004-08-17 07:31:39 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers - Bullet Proof Geckos ? Jon Elson 2004-08-17 10:15:36 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers Jon Elson 2004-08-17 10:18:13 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers Jon Elson 2004-08-17 10:24:49 UTC Re: [CAD_CAM_EDM_DRO] Re: burning Gecko drive Jon Elson 2004-08-17 10:33:25 UTC Re: [CAD_CAM_EDM_DRO] Re: burning Gecko drive Les Newell 2004-08-17 11:33:19 UTC Re: [CAD_CAM_EDM_DRO] Re: burning Gecko drive vavaroutsos 2004-08-17 11:34:08 UTC Re: burning Gecko drive turbulatordude 2004-08-17 13:42:29 UTC Re: wiring Gecko drivers - possibley bad steps JanRwl@A... 2004-08-17 14:12:27 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers Stephen Wille Padnos 2004-08-17 14:18:06 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers theokspindoctor 2004-08-17 18:07:17 UTC Re: wiring Gecko drivers Jon Elson 2004-08-17 18:42:14 UTC Re: [CAD_CAM_EDM_DRO] Re: burning Gecko drive JanRwl@A... 2004-08-17 20:50:33 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers theokspindoctor 2004-08-17 22:50:57 UTC Re: wiring Gecko drivers Les Newell 2004-08-18 01:22:13 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers