CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers

on 2004-08-17 14:18:06 UTC
JanRwl@... wrote:

>In a message dated 8/17/2004 12:22:08 AM Central Standard Time,
>mail@... writes:
>Does it make sense that the old Bridgeport motors can't handle the high rate
>or is it a problem of how I wired the motor. Do you think the 201s should be
>able to move a 200 step rev motor at over 60 ipm. <<
>No clue. Best you refer these questions to others in the group who WORK with
>BP's. Mine is manual, and I have no impetus to change it to CNC.
>
>Your second question: I assume you mean with 0.200"/turn screws? The 201's
>will want 2000 steps/turn. Then, 60 IPM = 300 TURNS per minute. 300 x
>2000=0.6 mHz. Hmmm... Dunno. Read the spec. sheet for "Max. f In"
>
I'd say this is off by a factor of 60.
300x2000 = 600ksteps/minute, not per second. It's a 10kHz pulse train.

- Steve

Discussion Thread

theokspindoctor 2004-08-16 20:05:47 UTC wiring Gecko drivers Robert Williams 2004-08-16 20:48:22 UTC Re: [CAD_CAM_EDM_DRO] wiring Gecko drivers theokspindoctor 2004-08-16 21:00:04 UTC Re: wiring Gecko drivers theokspindoctor 2004-08-16 21:12:13 UTC Re: wiring Gecko drivers Robert Williams 2004-08-16 21:23:03 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers JanRwl@A... 2004-08-16 21:32:19 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers theokspindoctor 2004-08-16 21:44:31 UTC Re: wiring Gecko drivers Jon Elson 2004-08-16 21:46:03 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers theokspindoctor 2004-08-16 21:49:37 UTC Re: wiring Gecko drivers theokspindoctor 2004-08-16 22:15:40 UTC Re: burning Gecko drive turbulatordude 2004-08-16 23:39:07 UTC Re: burning Gecko drive turbulatordude 2004-08-16 23:45:12 UTC Re: wiring Gecko drivers - power turbulatordude 2004-08-16 23:50:40 UTC Re: wiring Gecko drivers - light bulb turbulatordude 2004-08-16 23:52:12 UTC Re: wiring Gecko drivers - Bullet Proof Geckos ? Les Newell 2004-08-17 01:57:46 UTC Re: [CAD_CAM_EDM_DRO] Re: burning Gecko drive theokspindoctor 2004-08-17 05:23:37 UTC Re: burning Gecko drive Robert Williams 2004-08-17 06:25:13 UTC Re: [CAD_CAM_EDM_DRO] Re: burning Gecko drive Robert Williams 2004-08-17 07:03:33 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers Dan Mauch 2004-08-17 07:31:39 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers - Bullet Proof Geckos ? Jon Elson 2004-08-17 10:15:36 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers Jon Elson 2004-08-17 10:18:13 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers Jon Elson 2004-08-17 10:24:49 UTC Re: [CAD_CAM_EDM_DRO] Re: burning Gecko drive Jon Elson 2004-08-17 10:33:25 UTC Re: [CAD_CAM_EDM_DRO] Re: burning Gecko drive Les Newell 2004-08-17 11:33:19 UTC Re: [CAD_CAM_EDM_DRO] Re: burning Gecko drive vavaroutsos 2004-08-17 11:34:08 UTC Re: burning Gecko drive turbulatordude 2004-08-17 13:42:29 UTC Re: wiring Gecko drivers - possibley bad steps JanRwl@A... 2004-08-17 14:12:27 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers Stephen Wille Padnos 2004-08-17 14:18:06 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers theokspindoctor 2004-08-17 18:07:17 UTC Re: wiring Gecko drivers Jon Elson 2004-08-17 18:42:14 UTC Re: [CAD_CAM_EDM_DRO] Re: burning Gecko drive JanRwl@A... 2004-08-17 20:50:33 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers theokspindoctor 2004-08-17 22:50:57 UTC Re: wiring Gecko drivers Les Newell 2004-08-18 01:22:13 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers