CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers

Posted by Les Newell
on 2004-08-18 01:22:13 UTC
Reducing the stepper current will reduce low speed torque but will have
little effect on high speed torque. Due to the motor inductance the
current in the coils takes a finite time to reach the set current. At
high speeds the current in the coils never has time to reach the set
current. This is why steppers lose torque at speed.

Les

theokspindoctor wrote:

> The stepper rate seems not to be the problem. The GEckos are
> limited to 7 amps and the motors are rated at 9 amps unipolar and
> 12.7 amps bipolar. What does that mean in terms of how they are
> wired and how they will perform when using the lower amperage
> Gecko? Could that be the reason they only move at 20 ipm before
> stalling?
>
> Keith
>

Discussion Thread

theokspindoctor 2004-08-16 20:05:47 UTC wiring Gecko drivers Robert Williams 2004-08-16 20:48:22 UTC Re: [CAD_CAM_EDM_DRO] wiring Gecko drivers theokspindoctor 2004-08-16 21:00:04 UTC Re: wiring Gecko drivers theokspindoctor 2004-08-16 21:12:13 UTC Re: wiring Gecko drivers Robert Williams 2004-08-16 21:23:03 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers JanRwl@A... 2004-08-16 21:32:19 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers theokspindoctor 2004-08-16 21:44:31 UTC Re: wiring Gecko drivers Jon Elson 2004-08-16 21:46:03 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers theokspindoctor 2004-08-16 21:49:37 UTC Re: wiring Gecko drivers theokspindoctor 2004-08-16 22:15:40 UTC Re: burning Gecko drive turbulatordude 2004-08-16 23:39:07 UTC Re: burning Gecko drive turbulatordude 2004-08-16 23:45:12 UTC Re: wiring Gecko drivers - power turbulatordude 2004-08-16 23:50:40 UTC Re: wiring Gecko drivers - light bulb turbulatordude 2004-08-16 23:52:12 UTC Re: wiring Gecko drivers - Bullet Proof Geckos ? Les Newell 2004-08-17 01:57:46 UTC Re: [CAD_CAM_EDM_DRO] Re: burning Gecko drive theokspindoctor 2004-08-17 05:23:37 UTC Re: burning Gecko drive Robert Williams 2004-08-17 06:25:13 UTC Re: [CAD_CAM_EDM_DRO] Re: burning Gecko drive Robert Williams 2004-08-17 07:03:33 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers Dan Mauch 2004-08-17 07:31:39 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers - Bullet Proof Geckos ? Jon Elson 2004-08-17 10:15:36 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers Jon Elson 2004-08-17 10:18:13 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers Jon Elson 2004-08-17 10:24:49 UTC Re: [CAD_CAM_EDM_DRO] Re: burning Gecko drive Jon Elson 2004-08-17 10:33:25 UTC Re: [CAD_CAM_EDM_DRO] Re: burning Gecko drive Les Newell 2004-08-17 11:33:19 UTC Re: [CAD_CAM_EDM_DRO] Re: burning Gecko drive vavaroutsos 2004-08-17 11:34:08 UTC Re: burning Gecko drive turbulatordude 2004-08-17 13:42:29 UTC Re: wiring Gecko drivers - possibley bad steps JanRwl@A... 2004-08-17 14:12:27 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers Stephen Wille Padnos 2004-08-17 14:18:06 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers theokspindoctor 2004-08-17 18:07:17 UTC Re: wiring Gecko drivers Jon Elson 2004-08-17 18:42:14 UTC Re: [CAD_CAM_EDM_DRO] Re: burning Gecko drive JanRwl@A... 2004-08-17 20:50:33 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers theokspindoctor 2004-08-17 22:50:57 UTC Re: wiring Gecko drivers Les Newell 2004-08-18 01:22:13 UTC Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers