Re: wiring Gecko drivers
Posted by
theokspindoctor
on 2004-08-17 18:07:17 UTC
The stepper rate seems not to be the problem. The GEckos are
limited to 7 amps and the motors are rated at 9 amps unipolar and
12.7 amps bipolar. What does that mean in terms of how they are
wired and how they will perform when using the lower amperage
Gecko? Could that be the reason they only move at 20 ipm before
stalling?
Keith
--- In CAD_CAM_EDM_DRO@yahoogroups.com, Stephen Wille Padnos
<spadnos@s...> wrote:
limited to 7 amps and the motors are rated at 9 amps unipolar and
12.7 amps bipolar. What does that mean in terms of how they are
wired and how they will perform when using the lower amperage
Gecko? Could that be the reason they only move at 20 ipm before
stalling?
Keith
--- In CAD_CAM_EDM_DRO@yahoogroups.com, Stephen Wille Padnos
<spadnos@s...> wrote:
> JanRwl@A... wrote:the high rate
>
> >In a message dated 8/17/2004 12:22:08 AM Central Standard Time,
> >mail@t... writes:
> >Does it make sense that the old Bridgeport motors can't handle
> >or is it a problem of how I wired the motor. Do you think the201s should be
> >able to move a 200 step rev motor at over 60 ipm. <<who WORK with
> >No clue. Best you refer these questions to others in the group
> >BP's. Mine is manual, and I have no impetus to change it toCNC.
> >screws? The 201's
> >Your second question: I assume you mean with 0.200"/turn
> >will want 2000 steps/turn. Then, 60 IPM = 300 TURNS per minute.300 x
> >2000=0.6 mHz. Hmmm... Dunno. Read the spec. sheet for "Max. fIn"
> >train.
> I'd say this is off by a factor of 60.
> 300x2000 = 600ksteps/minute, not per second. It's a 10kHz pulse
>
> - Steve
Discussion Thread
theokspindoctor
2004-08-16 20:05:47 UTC
wiring Gecko drivers
Robert Williams
2004-08-16 20:48:22 UTC
Re: [CAD_CAM_EDM_DRO] wiring Gecko drivers
theokspindoctor
2004-08-16 21:00:04 UTC
Re: wiring Gecko drivers
theokspindoctor
2004-08-16 21:12:13 UTC
Re: wiring Gecko drivers
Robert Williams
2004-08-16 21:23:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers
JanRwl@A...
2004-08-16 21:32:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers
theokspindoctor
2004-08-16 21:44:31 UTC
Re: wiring Gecko drivers
Jon Elson
2004-08-16 21:46:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers
theokspindoctor
2004-08-16 21:49:37 UTC
Re: wiring Gecko drivers
theokspindoctor
2004-08-16 22:15:40 UTC
Re: burning Gecko drive
turbulatordude
2004-08-16 23:39:07 UTC
Re: burning Gecko drive
turbulatordude
2004-08-16 23:45:12 UTC
Re: wiring Gecko drivers - power
turbulatordude
2004-08-16 23:50:40 UTC
Re: wiring Gecko drivers - light bulb
turbulatordude
2004-08-16 23:52:12 UTC
Re: wiring Gecko drivers - Bullet Proof Geckos ?
Les Newell
2004-08-17 01:57:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: burning Gecko drive
theokspindoctor
2004-08-17 05:23:37 UTC
Re: burning Gecko drive
Robert Williams
2004-08-17 06:25:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: burning Gecko drive
Robert Williams
2004-08-17 07:03:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers
Dan Mauch
2004-08-17 07:31:39 UTC
Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers - Bullet Proof Geckos ?
Jon Elson
2004-08-17 10:15:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers
Jon Elson
2004-08-17 10:18:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers
Jon Elson
2004-08-17 10:24:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: burning Gecko drive
Jon Elson
2004-08-17 10:33:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: burning Gecko drive
Les Newell
2004-08-17 11:33:19 UTC
Re: [CAD_CAM_EDM_DRO] Re: burning Gecko drive
vavaroutsos
2004-08-17 11:34:08 UTC
Re: burning Gecko drive
turbulatordude
2004-08-17 13:42:29 UTC
Re: wiring Gecko drivers - possibley bad steps
JanRwl@A...
2004-08-17 14:12:27 UTC
Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers
Stephen Wille Padnos
2004-08-17 14:18:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers
theokspindoctor
2004-08-17 18:07:17 UTC
Re: wiring Gecko drivers
Jon Elson
2004-08-17 18:42:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: burning Gecko drive
JanRwl@A...
2004-08-17 20:50:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers
theokspindoctor
2004-08-17 22:50:57 UTC
Re: wiring Gecko drivers
Les Newell
2004-08-18 01:22:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: wiring Gecko drivers