Re: encoder
Posted by
alphawolf45
on 2004-09-25 16:49:16 UTC
Jon
Milli micro nano pico Heheheh Yeah I noticed his error also..Dunno
if you could remember Jon but this old Hurco project I am working on
now is one that I emailed you about June ,02 2002 and I printed out
your response to me and kept it..I feel like you done me some
good.Hang in there and thanks for the help.I dunno if I said that
before.
Steven---
In CAD_CAM_EDM_DRO@yahoogroups.com, Jon Elson <elson@p...> wrote:
Milli micro nano pico Heheheh Yeah I noticed his error also..Dunno
if you could remember Jon but this old Hurco project I am working on
now is one that I emailed you about June ,02 2002 and I printed out
your response to me and kept it..I feel like you done me some
good.Hang in there and thanks for the help.I dunno if I said that
before.
Steven---
In CAD_CAM_EDM_DRO@yahoogroups.com, Jon Elson <elson@p...> wrote:
> R Rogers wrote:less than .05 milliamp draw.
>
> >You probably need encoders. Geckos will only handle encoders with
> >(uA). You
> Not quite. 0.05 AMPS = 50 mA; .05 MilliAmps is 50 Microamps
> will NEVER find an encodergrating.
> that works on 50 uA, as it needs an LED to shine through the
> 50 mA is reasonable, but you
> may find some older encoders that draw more.
>
> Jon
Discussion Thread
alex
2003-02-18 08:26:47 UTC
encoder
motorworksnf
2003-09-02 18:23:57 UTC
encoder
Antonius J.M. Groothuizen
2003-09-02 18:44:35 UTC
Re: encoder
GRautoHP@a...
2004-09-24 14:39:05 UTC
encoder
Leslie Watts
2004-09-24 16:24:18 UTC
RE: [CAD_CAM_EDM_DRO] encoder
caudlet
2004-09-24 16:43:12 UTC
Re: encoder
GRautoHP@a...
2004-09-25 10:05:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: encoder
David Paulson
2004-09-25 10:10:54 UTC
Re: [CAD_CAM_EDM_DRO] Re: encoder
R Rogers
2004-09-25 14:57:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: encoder
Jon Elson
2004-09-25 16:26:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: encoder
alphawolf45
2004-09-25 16:49:16 UTC
Re: encoder
mohamed rashwan
2004-09-25 20:28:15 UTC
RE: [CAD_CAM_EDM_DRO] encoder
wanliker@a...
2004-09-25 20:37:47 UTC
Re: [CAD_CAM_EDM_DRO] encoder
R Rogers
2004-09-26 07:33:30 UTC
Re: [CAD_CAM_EDM_DRO] Re: encoder
GRautoHP@a...
2004-09-26 13:39:25 UTC
Re: [CAD_CAM_EDM_DRO] Re: encoder
turbulatordude
2004-09-26 18:17:48 UTC
PMM8714 5 phase stepper driver chip data sheet ??
mohamed rashwan
2004-09-27 06:27:46 UTC
Re: [CAD_CAM_EDM_DRO] PMM8714 5 phase stepper driver chip data sheet ??
turbulatordude
2004-09-27 06:49:57 UTC
5 phase stepper driver
deprince eddy
2006-02-19 05:36:37 UTC
encoder
ebiz_59
2008-04-24 10:13:23 UTC
encoder
David Speck
2008-04-24 10:20:53 UTC
Re: [CAD_CAM_EDM_DRO] encoder
Jon Elson
2008-04-24 20:13:14 UTC
Re: [CAD_CAM_EDM_DRO] encoder
stcnc2000
2008-04-25 07:57:45 UTC
Re: encoder
Mic
2008-04-25 09:42:28 UTC
Re: encoder