Re: [CAD_CAM_EDM_DRO] Why does my X axis go faster than my Y axis????

In Mach2Mach3, go into config at top of page click on motor tuning and setup, and increase the number in the step pulse 1-5 us and dir pulse 0-5, that may solve your problem, I had the same problem a while ago and that solved mine, try it!,

..................Edmund............another Mach3 user

Familia Peter Arce & TAD <peteryco@...> wrote:
How are the distances? how is the form?
When the wave sincronization (speed control per axis) of old timers is
of you get the most weared results.
Sven Peter

----- Mensaje Original -----
De: apples0_17
Fecha: Miercoles, Diciembre 21, 2005 5:55 am
Asunto: [CAD_CAM_EDM_DRO] Why does my X axis go faster than my Y axis????

> When I cut a part out using Mach3 my x axis will move faster that the
> y axis.
>
> For example:
>
> I have used a basic shape that has a couple 90 degree corners and a
> diagonal back to the start point.
>
> The shape is set to cut at 1300mm/min.
>
> The y axis will cut at 1300mm/min, but when the machine turns a corner
> and the x axis starts moving. The feed rated goes over the set
> 1300mm/min up to 1800mm/min.
>
> Then turns a corner and back onto the y axis and it is fine at
> 1300mm/min again.
>
> When doing an angle say 45degrees, it will move at 1400mm/min.
>
> What is going on???
>
>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
> wanliker@..., timg@...
> Moderator: pentam@... indigo_red@...
> davemucha@... [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to
> reach it if you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to
> be a sister site to the CCED group, as many of the same members
> are there, for OT subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING
> THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
>
>
>
>
>
>
>
>

Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com

Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@..., timg@...
Moderator: pentam@... indigo_red@... davemucha@... [Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO

OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
http://www.metalworking.com/news_servers.html

http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.

NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner


Yahoo! Groups Links











........Edmund.........


[Non-text portions of this message have been removed]