Re: [CAD_CAM_EDM_DRO] Why does my X axis go faster than my Y axis????

Peter, the trouble I had with my setup was my Y axis was loosing steps it would never end at zero on the handwheels index, it was only the Y every time, I could actually here the stepper missing, can you detect the motor missing with a slow feed say F1, also have you rechecked your steps per calculations, maybe a mistake there?, I would think as long as your steps per rev are correct in each axis and the way the motors are mounted it should work,
I think it might be best for you to contact Art Fenerty Mach2Mach3 cnc yahoo group and try to work it out with him, he is your best bet for sure,

PS, I only had to increase my step and dir up to a figure 4 in the boxes to smooth things out,

Sorry I cant help you more, I would hate to put you on the wrong track

....................................Edmund................



Peter Megan Isabella <apalais@...> wrote:
Ed,

I have them set to 9 for the step pulse(or maybe it was the direction).
Otherwise the motors sounded all rough.

Peter

----- Original Message -----
From: "ED MAISEY"
To:
Sent: Thursday, December 22, 2005 10:14 AM
Subject: Re: [CAD_CAM_EDM_DRO] Why does my X axis go faster than my Y
axis????


> In Mach2Mach3, go into config at top of page click on motor tuning and
> setup, and increase the number in the step pulse 1-5 us and dir pulse 0-5,
> that may solve your problem, I had the same problem a while ago and that
> solved mine, try it!,
>
> ..................Edmund............another Mach3 user
>
> Familia Peter Arce & TAD
wrote:
> How are the distances? how is the form?
> When the wave sincronization (speed control per axis) of old timers is
> of you get the most weared results.
> Sven Peter
>
> ----- Mensaje Original -----
> De: apples0_17
> Fecha: Miercoles, Diciembre 21, 2005 5:55 am
> Asunto: [CAD_CAM_EDM_DRO] Why does my X axis go faster than my Y axis????
>
>> When I cut a part out using Mach3 my x axis will move faster that the
>> y axis.
>>
>> For example:
>>
>> I have used a basic shape that has a couple 90 degree corners and a
>> diagonal back to the start point.
>>
>> The shape is set to cut at 1300mm/min.
>>
>> The y axis will cut at 1300mm/min, but when the machine turns a corner
>> and the x axis starts moving. The feed rated goes over the set
>> 1300mm/min up to 1800mm/min.
>>
>> Then turns a corner and back onto the y axis and it is fine at
>> 1300mm/min again.
>>
>> When doing an angle say 45degrees, it will move at 1400mm/min.
>>
>> What is going on???
>>
>>
>>
>>
>>
>> Addresses:
>> FAQ: http://www.ktmarketing.com/faq.html
>> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>>
>> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
>> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
>> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com,
>> wanliker@..., timg@...
>> Moderator: pentam@... indigo_red@...
>> davemucha@... [Moderators]
>> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>>
>> OFF Topic POSTS: General Machining
>> If you wish to post on unlimited OT subjects goto:
>> aol://5863:126/rec.crafts.metalworking or go thru Google.com to
>> reach it if you have trouble.
>> http://www.metalworking.com/news_servers.html
>>
>> http://groups.yahoo.com/group/jobshophomeshop I consider this to
>> be a sister site to the CCED group, as many of the same members
>> are there, for OT subjects, that are not allowed on the CCED list.
>>
>> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING
>> THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
>> bill
>> List Mom
>> List Owner
>>
>>
>> Yahoo! Groups Links
>>
>>
>>
>>
>>
>>
>>
>>
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
> timg@...
> Moderator: pentam@... indigo_red@... davemucha@...
> [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it
> if you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
> sister site to the CCED group, as many of the same members are there, for
> OT subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
> DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
>
>
>
>
>
>
>
>
>
>
>
> ........Edmund.........
>
>
> [Non-text portions of this message have been removed]
>
>
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
> Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com
>
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...,
> timg@...
> Moderator: pentam@... indigo_red@... davemucha@...
> [Moderators]
> URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
>
> OFF Topic POSTS: General Machining
> If you wish to post on unlimited OT subjects goto:
> aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it
> if you have trouble.
> http://www.metalworking.com/news_servers.html
>
> http://groups.yahoo.com/group/jobshophomeshop I consider this to be a
> sister site to the CCED group, as many of the same members are there, for
> OT subjects, that are not allowed on the CCED list.
>
> NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM.
> DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
> bill
> List Mom
> List Owner
>
>
> Yahoo! Groups Links
>
>
>
>
>
>
>
>
> --
> No virus found in this incoming message.
> Checked by AVG Free Edition.
> Version: 7.1.371 / Virus Database: 267.14.2/208 - Release Date: 20/12/2005
>



Addresses:
FAQ: http://www.ktmarketing.com/faq.html
FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
Post Messages: CAD_CAM_EDM_DRO@yahoogroups.com

Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@..., timg@...
Moderator: pentam@... indigo_red@... davemucha@... [Moderators]
URL to this group: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO

OFF Topic POSTS: General Machining
If you wish to post on unlimited OT subjects goto: aol://5863:126/rec.crafts.metalworking or go thru Google.com to reach it if you have trouble.
http://www.metalworking.com/news_servers.html

http://groups.yahoo.com/group/jobshophomeshop I consider this to be a sister site to the CCED group, as many of the same members are there, for OT subjects, that are not allowed on the CCED list.

NOTICE: ALL POSTINGS TO THIS GROUP BECOME PUBLIC DOMAIN BY POSTING THEM. DON'T POST IF YOU CAN NOT ACCEPT THIS.....NO EXCEPTIONS........
bill
List Mom
List Owner


Yahoo! Groups Links










........Edmund.........


[Non-text portions of this message have been removed]