Re: L297/L298 And a "correction"
Posted by
ballendo
on 2006-08-08 22:01:43 UTC
>In CCED, "Wayne C. Gramlich" <Wayne@...> wrote:Wayne,
>This was written about 2 years ago, so it is possible that some new
><$10/axis integrated MOSFET solution has been deployed. I certainly
>am not aware of any, but I haven't beeen looking recently.
The Sanken Chips sold by Allegro are under your price point, and
perform very nicely. The "problem" is that Sanken has been of
a "unipolar" mindset for many years.
I only wish Sanken and STS could run into each other (Reeses like)
saying,"Hey! you got microstepping in MY bipolar?!?
"Yeah?, Well you got bipolar in MY microstepping"
The STS L6208 with Sanken's uStep translator would be a nice chip
IMO. (or an SLA7078 with bipolar outputs; even better!)
Until then, the choice seems to be two LMD18245's or the Sanken chips
for 3amp drives...
Ballendo
Discussion Thread
TheDragonPit
1999-09-22 05:29:43 UTC
L297/L298
Phil Mattison
2006-08-04 08:53:05 UTC
L297/L298
vrsculptor
2006-08-04 09:18:58 UTC
Re: L297/L298
Jon Elson
2006-08-04 09:42:09 UTC
Re: [CAD_CAM_EDM_DRO] L297/L298
Lester Caine
2006-08-04 09:46:23 UTC
Re: [CAD_CAM_EDM_DRO] L297/L298
Wayne C. Gramlich
2006-08-04 10:34:25 UTC
Re: L297/L298
Phil Mattison
2006-08-04 11:17:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: L297/L298
Lester Caine
2006-08-04 12:51:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: L297/L298
John Dammeyer
2006-08-04 13:22:58 UTC
RE: [CAD_CAM_EDM_DRO] Re: L297/L298
Sebastien Bailard - Dubsen
2006-08-04 14:18:42 UTC
Re: [CAD_CAM_EDM_DRO] Re: L297/L298
JanRwl@A...
2006-08-04 14:55:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: L297/L298
ballendo
2006-08-04 15:07:45 UTC
Re: L297/L298 And a "correction"
Alan Marconett
2006-08-04 15:18:52 UTC
RE: [CAD_CAM_EDM_DRO] L297/L298
John Dammeyer
2006-08-04 15:29:14 UTC
RE: [CAD_CAM_EDM_DRO] Re: L297/L298
Phil Mattison
2006-08-04 16:49:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: L297/L298 And a "correction"
Doug Fortune
2006-08-04 17:27:23 UTC
Looking for mini-VFD for 120VAC/1ph
Lee Studley
2006-08-04 20:17:14 UTC
Re: Looking for mini-VFD for 120VAC/1ph
afogassa
2006-08-04 20:33:32 UTC
Re: Looking for mini-VFD for 120VAC/1ph
caudlet
2006-08-04 21:11:38 UTC
Re: Looking for mini-VFD for 120VAC/1ph
P. J. Hicks
2006-08-04 21:41:10 UTC
Cameras
JanRwl@A...
2006-08-04 21:57:27 UTC
Re: [CAD_CAM_EDM_DRO] Looking for mini-VFD for 120VAC/1ph
JanRwl@A...
2006-08-04 22:11:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: Looking for mini-VFD for 120VAC/1ph
Peter Reilley
2006-08-05 06:16:17 UTC
Re: [CAD_CAM_EDM_DRO] Cameras
caudlet
2006-08-05 07:06:17 UTC
Re: Looking for mini-VFD for 120VAC/1ph
Doug Fortune
2006-08-05 08:38:59 UTC
Re: Looking for mini-VFD for 120VAC/1ph
Alan Marconett
2006-08-05 09:20:33 UTC
Re: [CAD_CAM_EDM_DRO] Looking for mini-VFD for 120VAC/1ph
turbulatordude
2006-08-05 09:35:13 UTC
Re: Looking for mini-VFD for 120VAC/1ph
ballendo
2006-08-05 11:26:45 UTC
Re: L297/L298 And a "correction"
ballendo
2006-08-05 11:29:13 UTC
Re: Looking for mini-VFD for 120VAC/1ph
ballendo
2006-08-05 11:31:37 UTC
OT Re: Looking for mini-VFD for 120VAC/1ph
Wayne C. Gramlich
2006-08-07 20:50:07 UTC
Re: L297/L298
Phil Mattison
2006-08-08 07:31:40 UTC
Re: L297/L298
Lester Caine
2006-08-08 11:58:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: L297/L298
Wayne C. Gramlich
2006-08-08 21:13:53 UTC
Re: L297/L298 And a "correction"
Mariss Freimanis
2006-08-08 21:34:55 UTC
Re: L297/L298 And a "correction"
ballendo
2006-08-08 22:01:43 UTC
Re: L297/L298 And a "correction"
Jon Elson
2006-08-08 22:53:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: L297/L298 And a "correction"
Wayne C. Gramlich
2006-08-09 10:01:20 UTC
Re: L297/L298 And a "correction"
John Dammeyer
2006-08-09 10:17:28 UTC
RE: [CAD_CAM_EDM_DRO] Re: L297/L298 And a "correction"
Alan Marconett
2006-08-09 10:47:18 UTC
RE: [CAD_CAM_EDM_DRO] Re: L297/L298 And a "correction"
Wayne C. Gramlich
2006-08-11 22:18:42 UTC
Re: L297/L298 And a "correction"
Lester Caine
2006-08-11 23:01:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: L297/L298 And a "correction"
Wayne C. Gramlich
2006-08-13 11:00:29 UTC
Re: L297/L298 And a "correction"
Lester Caine
2006-08-13 13:03:35 UTC
Re: [CAD_CAM_EDM_DRO] Re: L297/L298 And a "correction"
Steve Blackmore
2006-08-13 16:53:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: L297/L298 And a "correction"
Lester Caine
2006-08-13 23:05:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: L297/L298 And a "correction"
Vlad Krupin
2006-09-01 22:47:16 UTC
Re: [CAD_CAM_EDM_DRO] L297/L298
turbulatordude
2006-09-02 08:53:04 UTC
Re: L297/L298
Vlad Krupin
2006-09-02 22:16:37 UTC
Re: [CAD_CAM_EDM_DRO] Re: L297/L298