Re: Servo controllers for table top machines.
Posted by
turbulatordude
on 2006-12-17 08:35:24 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "enytned1" <alexkcpr@...> wrote:
Is that a whole new machine ?
A power supply would cost less than $500.00, 3 drives less than
another $500.00, 3 motors, depending on costs, anywhere from $20.00
treadmill motors to $350 servos. Encoders would run about $200.00 for
the three, depending on options. may come with 'real' servo-motor.
I think you would be hard pressed to spend $2,000 on a complete servo
system.
Dave
>$3,500 for an upgrade ?
> "It trades speed you can't use for torque you can." What??????
>
> I was under the impression I could just bolt on the brush type servo
> motors directly to the ball screw end, similar to the way my stepper
> motors are connected currently.
> How do DC-servo motors with 500CPR encoders with Gecko 320drives
> compare to a micro stepping motor and driver in terms of
> repeatability, precision etc?
>
> The old techno controller I use was originally setup for full step
> mode I have changed this to half step mode and have seen an immediate
> improvement. How reliable are these controllers you mentioned? I
> know I can get a 4-axis upgrade from Techno for about $3500.00 but I'm
> not sure if I can convert it to run of Mach3?
Is that a whole new machine ?
A power supply would cost less than $500.00, 3 drives less than
another $500.00, 3 motors, depending on costs, anywhere from $20.00
treadmill motors to $350 servos. Encoders would run about $200.00 for
the three, depending on options. may come with 'real' servo-motor.
I think you would be hard pressed to spend $2,000 on a complete servo
system.
Dave
Discussion Thread
enytned1
2006-12-15 15:31:16 UTC
Servo controllers for table top machines.
Anders Wallin
2006-12-16 02:54:41 UTC
Re: [CAD_CAM_EDM_DRO] Servo controllers for table top machines.
caudlet
2006-12-16 08:09:16 UTC
Re: Servo controllers for table top machines.
enytned1
2006-12-16 15:50:12 UTC
Re: Servo controllers for table top machines.
Mariss Freimanis
2006-12-16 22:01:40 UTC
Re: Servo controllers for table top machines.
Leslie Newell
2006-12-17 02:18:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo controllers for table top machines.
turbulatordude
2006-12-17 08:35:24 UTC
Re: Servo controllers for table top machines.
Dan Mauch
2006-12-17 08:49:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo controllers for table top machines.
John Dammeyer
2006-12-17 15:42:35 UTC
RE: [CAD_CAM_EDM_DRO] Re: Servo controllers for table top machines.
enytned1
2006-12-17 16:58:27 UTC
Re: Servo controllers for table top machines.
Mariss Freimanis
2006-12-17 17:46:37 UTC
Re: Servo controllers for table top machines.
Steve Blackmore
2006-12-17 17:49:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo controllers for table top machines.
Leslie Newell
2006-12-18 01:57:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo controllers for table top machines.
Leslie Newell
2006-12-18 02:39:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo controllers for table top machines.
Polaraligned
2006-12-18 04:52:37 UTC
Re: Servo controllers for table top machines.
David Bloomfield
2006-12-18 05:28:56 UTC
Re: Servo controllers for table top machines.
Fred Smith
2006-12-18 05:56:36 UTC
Re: Servo controllers for table top machines.
enytned1
2006-12-18 08:07:40 UTC
Re: Servo controllers for table top machines.
turbulatordude
2006-12-18 08:55:03 UTC
Re: Servo controllers for table top machines. long
Fred Smith
2006-12-18 11:07:30 UTC
Re: Servo controllers for table top machines.
Leslie Newell
2006-12-18 11:51:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo controllers for table top machines.
Leslie Newell
2006-12-18 12:00:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo controllers for table top machines. long
Steve Blackmore
2006-12-18 15:26:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo controllers for table top machines.
Leslie Newell
2006-12-18 17:16:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo controllers for table top machines.
turbulatordude
2006-12-19 04:29:10 UTC
Re: Servo controllers for table top machines. long
William Carr
2006-12-26 07:05:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo controllers for table top machines.
lcdpublishing
2006-12-26 07:41:47 UTC
Re: Servo controllers for table top machines.
Jon Elson
2006-12-26 11:05:56 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo controllers for table top machines.