RE: [CAD_CAM_EDM_DRO] Re: Servo controllers for table top machines.
Posted by
John Dammeyer
on 2006-12-17 15:42:35 UTC
Hi,
I'm always a bit confused when I see magic numbers without the math behind
them.
So here are the conversions,
From http://www.zeroggraphics.com/Portfolio/Torque-Conversion-Chart.pdf
700 oz-in is the same as 3.64 ft-lbs
From http://en.wikipedia.org/wiki/Horsepower
HP = Torque (ft-lb) * RPM
---------------------
5252
So we have 3.64 * 500
---------- = 0.347HP
5252
Also from the same link,
1 HP is equivalent to 746W
Therefore 746W/HP * 0.347HP = 258W
John Dammeyer
I'm always a bit confused when I see magic numbers without the math behind
them.
So here are the conversions,
From http://www.zeroggraphics.com/Portfolio/Torque-Conversion-Chart.pdf
700 oz-in is the same as 3.64 ft-lbs
From http://en.wikipedia.org/wiki/Horsepower
HP = Torque (ft-lb) * RPM
---------------------
5252
So we have 3.64 * 500
---------- = 0.347HP
5252
Also from the same link,
1 HP is equivalent to 746W
Therefore 746W/HP * 0.347HP = 258W
John Dammeyer
> Subject: [CAD_CAM_EDM_DRO] Re: Servo controllers for table
> top machines.
>
>
> > I was under the impression I could just bolt on the brush type servo
> > motors directly to the ball screw end, similar to the way my stepper
> > motors are connected currently.
>
> No... You can't (unless you're looking to burn your brand-new
> servomotor down in 5 minutes or less).
>
> Rule #1: Servomotors are not step motors.
>
> --------------------------
> Typical NEMA-34 step motor: Develops 700 in-oz of torque out to 500
> RPM for a power output of 260 Watts. The motor gets too hot to touch
> (perfectly normal) at 7A and 80VDC.
>
> Mariss
Discussion Thread
enytned1
2006-12-15 15:31:16 UTC
Servo controllers for table top machines.
Anders Wallin
2006-12-16 02:54:41 UTC
Re: [CAD_CAM_EDM_DRO] Servo controllers for table top machines.
caudlet
2006-12-16 08:09:16 UTC
Re: Servo controllers for table top machines.
enytned1
2006-12-16 15:50:12 UTC
Re: Servo controllers for table top machines.
Mariss Freimanis
2006-12-16 22:01:40 UTC
Re: Servo controllers for table top machines.
Leslie Newell
2006-12-17 02:18:06 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo controllers for table top machines.
turbulatordude
2006-12-17 08:35:24 UTC
Re: Servo controllers for table top machines.
Dan Mauch
2006-12-17 08:49:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo controllers for table top machines.
John Dammeyer
2006-12-17 15:42:35 UTC
RE: [CAD_CAM_EDM_DRO] Re: Servo controllers for table top machines.
enytned1
2006-12-17 16:58:27 UTC
Re: Servo controllers for table top machines.
Mariss Freimanis
2006-12-17 17:46:37 UTC
Re: Servo controllers for table top machines.
Steve Blackmore
2006-12-17 17:49:55 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo controllers for table top machines.
Leslie Newell
2006-12-18 01:57:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo controllers for table top machines.
Leslie Newell
2006-12-18 02:39:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo controllers for table top machines.
Polaraligned
2006-12-18 04:52:37 UTC
Re: Servo controllers for table top machines.
David Bloomfield
2006-12-18 05:28:56 UTC
Re: Servo controllers for table top machines.
Fred Smith
2006-12-18 05:56:36 UTC
Re: Servo controllers for table top machines.
enytned1
2006-12-18 08:07:40 UTC
Re: Servo controllers for table top machines.
turbulatordude
2006-12-18 08:55:03 UTC
Re: Servo controllers for table top machines. long
Fred Smith
2006-12-18 11:07:30 UTC
Re: Servo controllers for table top machines.
Leslie Newell
2006-12-18 11:51:32 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo controllers for table top machines.
Leslie Newell
2006-12-18 12:00:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo controllers for table top machines. long
Steve Blackmore
2006-12-18 15:26:29 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo controllers for table top machines.
Leslie Newell
2006-12-18 17:16:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo controllers for table top machines.
turbulatordude
2006-12-19 04:29:10 UTC
Re: Servo controllers for table top machines. long
William Carr
2006-12-26 07:05:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo controllers for table top machines.
lcdpublishing
2006-12-26 07:41:47 UTC
Re: Servo controllers for table top machines.
Jon Elson
2006-12-26 11:05:56 UTC
Re: [CAD_CAM_EDM_DRO] Re: Servo controllers for table top machines.