Re: New member
Posted by
Graham Stabler
on 2007-06-21 01:59:43 UTC
--- In CAD_CAM_EDM_DRO@yahoogroups.com, "Nigel Lawton"
<nigellawton009@...> wrote:
don't think my website shows any metal milling, for some reason most
of that has been done for other people so I wanted to highlight the
fact it could do it well. I made one part in particular that required
multiple setups and many narrow pockets to be created, the guys in the
mechanical workshop where I worked were very impressed by the finish I
got on the small details. Unfortunately the part is not mine and I
forgot to photograph it!
I can make a further recommendation of a little vice, the 1" wide Pin
Type Precision Vice sold by Chronos Ref: SITMV0001 It's a great little
vice for the proxxon, most just seem too big or are a bit rubbish.
Also good on a sherline I should say, a clever design.
Graham
<nigellawton009@...> wrote:
> Sorry if I have wasted your fingers! Many thanks forNot a problem, I like preaching even to the converted :) Actually I
> your advice!
>
don't think my website shows any metal milling, for some reason most
of that has been done for other people so I wanted to highlight the
fact it could do it well. I made one part in particular that required
multiple setups and many narrow pockets to be created, the guys in the
mechanical workshop where I worked were very impressed by the finish I
got on the small details. Unfortunately the part is not mine and I
forgot to photograph it!
I can make a further recommendation of a little vice, the 1" wide Pin
Type Precision Vice sold by Chronos Ref: SITMV0001 It's a great little
vice for the proxxon, most just seem too big or are a bit rubbish.
Also good on a sherline I should say, a clever design.
Graham
Discussion Thread
Colin Robson
1999-05-20 10:54:49 UTC
New member
m_olszta@x...
1999-10-29 09:18:57 UTC
New member
GAUTAM BACHHAWAT
2001-01-21 09:05:16 UTC
New member
Les Watts
2001-01-21 10:53:52 UTC
Re: [CAD_CAM_EDM_DRO] New member
Smoke
2001-01-21 12:41:34 UTC
Re: [CAD_CAM_EDM_DRO] New member
GAUTAM BACHHAWAT
2001-01-22 22:35:20 UTC
Re: [CAD_CAM_EDM_DRO] New member
Smoke
2001-01-22 22:57:25 UTC
Re: [CAD_CAM_EDM_DRO] New member
GAUTAM BACHHAWAT
2001-01-22 23:01:09 UTC
Re: [CAD_CAM_EDM_DRO] New member
Angelos
2001-12-27 15:00:56 UTC
New member
aerobscure
2003-01-29 14:52:42 UTC
New member
ballendo <ballendo@y...
2003-01-31 07:03:19 UTC
Re: New member
drusso59
2003-07-26 06:51:40 UTC
New member
Tim Goldstein
2003-07-26 07:07:43 UTC
RE: [CAD_CAM_EDM_DRO] New member
Charles Hixon
2003-07-26 08:34:28 UTC
Re: New member
alanenourse
2004-10-15 16:33:05 UTC
New member
pasofinojls99
2006-06-09 12:55:32 UTC
New member
BRIAN FOLEY
2006-06-09 14:24:20 UTC
Re: [CAD_CAM_EDM_DRO] New member
wanliker@a...
2006-06-09 16:14:19 UTC
New member
wanliker@a...
2006-06-09 16:54:13 UTC
New member
DEN SWEENEY
2006-06-13 04:59:03 UTC
Re: [CAD_CAM_EDM_DRO] New member
Nigel Lawton
2007-06-20 06:58:00 UTC
New member
Graham Stabler
2007-06-20 08:09:33 UTC
Re: New member
Alan KM6VV
2007-06-20 08:20:07 UTC
RE: [CAD_CAM_EDM_DRO] New member
Nigel Lawton
2007-06-20 18:48:10 UTC
Re: New member
Nigel Lawton
2007-06-20 18:50:34 UTC
Re: New member
Alan KM6VV
2007-06-20 19:35:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: New member
Graham Stabler
2007-06-21 01:40:40 UTC
Re: New member
Graham Stabler
2007-06-21 01:59:43 UTC
Re: New member
gawnca
2007-06-21 05:42:13 UTC
Re: New member
Jeff Demand
2007-06-21 09:05:31 UTC
Re: New member
Nigel Lawton
2007-06-22 06:30:17 UTC
Re: New member
Nigel Lawton
2007-06-22 06:30:20 UTC
Re: New member