CAD CAM EDM DRO - Yahoo Group Archive

Re: New member

Posted by Nigel Lawton
on 2007-06-22 06:30:17 UTC
Alan,
Many thanks
Regards
Nigel
--- In CAD_CAM_EDM_DRO@yahoogroups.com, Alan KM6VV <KM6VV@...> wrote:
>
> Hi Nigel,
>
> I'd bet you could get it without the PC, if desired. You'd have
to
> install EMC. The PC hard drive can be partitioned, and the PC
made to
> boot in either Linux or Windows if desired.
>
> I believe there is a distributor in the UK.
>
> Spindle motors are 100VAC to 240 VAC, 50 Hz or 60 Hz, so no
worries there.
>
> http://www.sherline.com/specs.htm
>
> Also see the Sherline list.
>
> Best Regards,
>
> Alan KM6VV
>
>
> Nigel Lawton wrote:
>
> >Alan,
> >Many thanks for your welcome.
> >Looking at Sheline.com on the face of it could be significantly
more
> >expensive than MaxNC or Proxxon M70, but does seem to include a
PC
> >(but these are REALLY cheap now). However one technical question
> >arises for a UK person (though I do visit California reasonable
> >often). Are these available in UK and is a 240V option available?
> >Regards
> >Nigel
> >
>

Discussion Thread

Colin Robson 1999-05-20 10:54:49 UTC New member m_olszta@x... 1999-10-29 09:18:57 UTC New member GAUTAM BACHHAWAT 2001-01-21 09:05:16 UTC New member Les Watts 2001-01-21 10:53:52 UTC Re: [CAD_CAM_EDM_DRO] New member Smoke 2001-01-21 12:41:34 UTC Re: [CAD_CAM_EDM_DRO] New member GAUTAM BACHHAWAT 2001-01-22 22:35:20 UTC Re: [CAD_CAM_EDM_DRO] New member Smoke 2001-01-22 22:57:25 UTC Re: [CAD_CAM_EDM_DRO] New member GAUTAM BACHHAWAT 2001-01-22 23:01:09 UTC Re: [CAD_CAM_EDM_DRO] New member Angelos 2001-12-27 15:00:56 UTC New member aerobscure 2003-01-29 14:52:42 UTC New member ballendo <ballendo@y... 2003-01-31 07:03:19 UTC Re: New member drusso59 2003-07-26 06:51:40 UTC New member Tim Goldstein 2003-07-26 07:07:43 UTC RE: [CAD_CAM_EDM_DRO] New member Charles Hixon 2003-07-26 08:34:28 UTC Re: New member alanenourse 2004-10-15 16:33:05 UTC New member pasofinojls99 2006-06-09 12:55:32 UTC New member BRIAN FOLEY 2006-06-09 14:24:20 UTC Re: [CAD_CAM_EDM_DRO] New member wanliker@a... 2006-06-09 16:14:19 UTC New member wanliker@a... 2006-06-09 16:54:13 UTC New member DEN SWEENEY 2006-06-13 04:59:03 UTC Re: [CAD_CAM_EDM_DRO] New member Nigel Lawton 2007-06-20 06:58:00 UTC New member Graham Stabler 2007-06-20 08:09:33 UTC Re: New member Alan KM6VV 2007-06-20 08:20:07 UTC RE: [CAD_CAM_EDM_DRO] New member Nigel Lawton 2007-06-20 18:48:10 UTC Re: New member Nigel Lawton 2007-06-20 18:50:34 UTC Re: New member Alan KM6VV 2007-06-20 19:35:46 UTC Re: [CAD_CAM_EDM_DRO] Re: New member Graham Stabler 2007-06-21 01:40:40 UTC Re: New member Graham Stabler 2007-06-21 01:59:43 UTC Re: New member gawnca 2007-06-21 05:42:13 UTC Re: New member Jeff Demand 2007-06-21 09:05:31 UTC Re: New member Nigel Lawton 2007-06-22 06:30:17 UTC Re: New member Nigel Lawton 2007-06-22 06:30:20 UTC Re: New member