CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit

Posted by ptengin@a...
on 2000-08-26 02:53:17 UTC
In a message dated 08/25/2000 1:36:55 AM Hawaiian Standard Time,
Area51tats@... writes:

<< good general rule of thumb for press fit is .001 for every 1 inch of
diameter. it also depends on the material that you are using

Gerald
>>
Gerald,

True on general press fits. Not always best for high precision ball
bearings. In this case we are supposed to be using matched pair single row
angular contact bearings. Depending on how these are setup, either the out
side or inside pair of races need to have a slip fit so the preload can be
adjusted. The other pair of races would usually be a light press fit and
held in place with a bolted retainer or adjusting ring. FYI

Peter
THRD, Inc.

Discussion Thread

ptengin@a... 2000-08-18 19:06:09 UTC Re: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit Mike Gann 2000-08-18 20:42:40 UTC Re: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit ptengin@a... 2000-08-18 20:55:28 UTC Re: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit Mike Gann 2000-08-18 21:04:47 UTC Re: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit Ian Wright 2000-08-19 01:19:31 UTC Re: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit Terry May 2000-08-19 08:06:11 UTC Re: RF-45 Retrofit Terry May 2000-08-19 08:17:51 UTC Re: RF-45 Retrofit Tim Goldstein 2000-08-19 11:28:39 UTC RE: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit Terry May 2000-08-19 11:37:25 UTC Re: RF-45 Retrofit ptengin@a... 2000-08-19 15:56:18 UTC Re: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit ptengin@a... 2000-08-23 17:24:50 UTC Re: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit Terry May 2000-08-24 16:24:20 UTC Re: RF-45 Retrofit ptengin@a... 2000-08-25 03:07:44 UTC Re: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit ptengin@a... 2000-08-25 03:21:03 UTC Re: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit Area51tats@a... 2000-08-25 04:36:18 UTC Re: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit Terry May 2000-08-25 15:33:13 UTC Re: RF-45 Retrofit Carlos Guillermo 2000-08-25 18:13:13 UTC RE: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit ptengin@a... 2000-08-26 02:53:17 UTC Re: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit ptengin@a... 2000-08-26 03:31:38 UTC Re: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit Terry May 2000-08-26 15:18:22 UTC Re: RF-45 Retrofit dave engvall 2000-08-26 19:31:51 UTC Re: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit Tim Goldstein 2000-08-26 21:12:56 UTC Treadmill motors and interference Ejay Hire 2000-08-27 09:02:18 UTC Re: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit