Re: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit
Posted by
Area51tats@a...
on 2000-08-25 04:36:18 UTC
good general rule of thumb for press fit is .001 for every 1 inch of
diameter. it also depends on the material that you are using
Gerald
diameter. it also depends on the material that you are using
Gerald
Discussion Thread
ptengin@a...
2000-08-18 19:06:09 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit
Mike Gann
2000-08-18 20:42:40 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit
ptengin@a...
2000-08-18 20:55:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit
Mike Gann
2000-08-18 21:04:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit
Ian Wright
2000-08-19 01:19:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit
Terry May
2000-08-19 08:06:11 UTC
Re: RF-45 Retrofit
Terry May
2000-08-19 08:17:51 UTC
Re: RF-45 Retrofit
Tim Goldstein
2000-08-19 11:28:39 UTC
RE: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit
Terry May
2000-08-19 11:37:25 UTC
Re: RF-45 Retrofit
ptengin@a...
2000-08-19 15:56:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit
ptengin@a...
2000-08-23 17:24:50 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit
Terry May
2000-08-24 16:24:20 UTC
Re: RF-45 Retrofit
ptengin@a...
2000-08-25 03:07:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit
ptengin@a...
2000-08-25 03:21:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit
Area51tats@a...
2000-08-25 04:36:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit
Terry May
2000-08-25 15:33:13 UTC
Re: RF-45 Retrofit
Carlos Guillermo
2000-08-25 18:13:13 UTC
RE: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit
ptengin@a...
2000-08-26 02:53:17 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit
ptengin@a...
2000-08-26 03:31:38 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit
Terry May
2000-08-26 15:18:22 UTC
Re: RF-45 Retrofit
dave engvall
2000-08-26 19:31:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit
Tim Goldstein
2000-08-26 21:12:56 UTC
Treadmill motors and interference
Ejay Hire
2000-08-27 09:02:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: RF-45 Retrofit