CAD CAM EDM DRO - Yahoo Group Archive

Re: Encoders

Posted by Dan Mauch
on 1999-06-30 08:40:01 UTC
I am using one of the HEDS9100 and a 1000 count - 4000 quadrature encoder.
It works fine with the board.
Dan
-----Original Message-----
From: Tim Goldstein <timg@...>
To: CAD_CAM_EDM_DRO@onelist.com <CAD_CAM_EDM_DRO@onelist.com>
Date: Wednesday, June 30, 1999 8:10 AM
Subject: Re: [CAD_CAM_EDM_DRO] Encoders


>From: "Tim Goldstein" <timg@...>
>
>Jon,
>
>Looking into these encoders they are HEDS9100 A00 set up with 1000 slot
>wheels.
>Does your endorsement for servo use still apply?
>
>Will they work well for the DRO boards Dan has made up?
>
>Tim
>[Denver,CO]
>
>
>----- Original Message -----
>From: Jon Elson <jmelson@...>
>To: <CAD_CAM_EDM_DRO@onelist.com>
>Sent: Wednesday, June 30, 1999 12:25 AM
>Subject: Re: [CAD_CAM_EDM_DRO] Encoders
>
>
>> From: Jon Elson <jmelson@...>
>>
>>
>>
>> Tim Goldstein wrote:
>>
>> > From: "Tim Goldstein" <timg@...>
>> >
>> > Jon,
>> >
>> > How would a HP HEDS 9100 head with a 1,000 slot disk work as an encoder
>for
>> > servo systems?
>>
>> Very well. the only thing better would be the HEDS-9040-B00, which adds
>an
>> index channel to the 1000 cycle encoder. either of these will give 4000
>counts/rev.
>>
>> I would have used these if I hadn't found complete encoders, surplus.
>>
>> Jon
>>
>>
>> --------------------------- ONElist Sponsor ----------------------------
>>
>> What do fashion and football have in common?
>> http://www.onelist.com
>> They both have communities at ONElist. Find yours today!
>>
>> ------------------------------------------------------------------------
>> Welcome to CAD_CAM_EDM_DRO@...,an unmodulated list for the
>discussion of shop built systems in the above catagories.
>> To Unsubscribe, read archives, change to or from digest.
>> Go to: http://www.onelist.com/isregistered.cgi
>> Log on, and you will go to Member Center, and you can make changes there.
>> bill,
>> List Manager
>>
>
>
>--------------------------- ONElist Sponsor ----------------------------
>
>ONElist members are using Shared Files in great ways!
>http://www.onelist.com
>Are you? If not, see our homepage for details.
>
>------------------------------------------------------------------------
>Welcome to CAD_CAM_EDM_DRO@...,an unmodulated list for the
discussion of shop built systems in the above catagories.
>To Unsubscribe, read archives, change to or from digest.
>Go to: http://www.onelist.com/isregistered.cgi
>Log on, and you will go to Member Center, and you can make changes there.
>bill,
>List Manager
>

Discussion Thread

Jon Elson 1999-06-28 23:31:30 UTC Re: Encoders Tim Goldstein 1999-06-29 16:27:22 UTC Re: Encoders Jon Elson 1999-06-29 23:25:29 UTC Re: Encoders Tim Goldstein 1999-06-30 08:08:50 UTC Re: Encoders Dan Mauch 1999-06-30 08:40:01 UTC Re: Encoders Jon Elson 1999-06-30 23:04:21 UTC Re: Encoders Laverne Karras 1999-07-01 18:26:50 UTC Re: Encoders Ron Brown 1999-07-11 07:03:23 UTC Encoders Ted Robbins 1999-07-15 10:16:02 UTC Encoders William Scalione 2000-06-15 18:40:55 UTC Encoders Ian Wright 2001-08-27 05:27:33 UTC Encoders Jon Elson 2001-08-27 11:46:07 UTC Re: [CAD_CAM_EDM_DRO] Encoders Ian Wright 2001-08-27 12:47:29 UTC Re: [CAD_CAM_EDM_DRO] Encoders Alan Marconett KM6VV 2001-08-27 12:51:11 UTC Re: [CAD_CAM_EDM_DRO] Encoders Jon Elson 2001-08-27 21:15:03 UTC Re: [CAD_CAM_EDM_DRO] Encoders Joseph 2001-08-27 22:47:10 UTC Re: Encoders Frank Cohn 2001-10-16 01:46:03 UTC Encoders Alan Marconett KM6VV 2001-10-16 10:41:19 UTC Re: [CAD_CAM_EDM_DRO] Encoders marble_h 2002-02-02 19:21:24 UTC Encoders Lew 2002-02-02 19:29:54 UTC RE: [CAD_CAM_EDM_DRO] Encoders marble_h 2002-02-02 19:53:40 UTC Re: Encoders Francisco Simon 2002-10-11 02:56:36 UTC Encoders dakota8833 2002-10-11 06:43:24 UTC Re: Encoders marc_e_davis 2002-11-20 11:23:29 UTC Encoders deanc500 2002-11-20 11:55:35 UTC Re: Encoders Tim Goldstein 2002-11-20 12:44:25 UTC Re: [CAD_CAM_EDM_DRO] Encoders Bob Simon 2002-11-20 16:52:46 UTC Re: [CAD_CAM_EDM_DRO] Encoders Jon Elson 2002-11-20 21:26:39 UTC Re: [CAD_CAM_EDM_DRO] Encoders Tim Goldstein 2003-12-24 21:45:45 UTC Re:Re: Encoders Tony Jeffree 2003-12-25 00:02:39 UTC Re: [CAD_CAM_EDM_DRO] Re:Re: Encoders Tim Goldstein 2003-12-25 09:02:30 UTC RE: [CAD_CAM_EDM_DRO] Encoders Jon Elson 2003-12-25 11:21:06 UTC Re: [CAD_CAM_EDM_DRO] Re:Re: Encoders Gregory Kamysz 2003-12-25 13:57:57 UTC Re: [CAD_CAM_EDM_DRO] Re:Re: Encoders Tony Jeffree 2003-12-25 15:20:36 UTC RE: [CAD_CAM_EDM_DRO] Encoders Bruce Pigeon 2005-02-15 09:07:58 UTC Encoders Ron Kline 2005-02-15 18:01:48 UTC Caps ?? Dave Fisher 2005-02-15 18:19:20 UTC RE: [CAD_CAM_EDM_DRO] Caps ?? R Rogers 2005-02-15 18:19:59 UTC Re: [CAD_CAM_EDM_DRO] Caps ?? JanRwl@A... 2005-02-16 16:41:40 UTC Re: [CAD_CAM_EDM_DRO] Caps ?? Robert Campbell 2005-02-16 16:48:34 UTC Re: [CAD_CAM_EDM_DRO] Caps ?? JanRwl@A... 2005-02-16 22:40:17 UTC Re: [CAD_CAM_EDM_DRO] Caps ?? pwshahood 2005-02-17 10:45:30 UTC Re: Caps ??