Re: [CAD_CAM_EDM_DRO] Re: Timing Belt Sizing
Posted by
Carey L. Culpepper
on 2000-11-27 18:46:31 UTC
Wally: I am running NEMA 42 size stepper motors. I also have a 1850 oz. in stepper but have not mounted it. The 3 motors that I have
mounted on my Bridgeport have encoders that I may use to go closed loop.They are Compumotor made by Eastern Air Devices.
Wally K wrote:
mounted on my Bridgeport have encoders that I may use to go closed loop.They are Compumotor made by Eastern Air Devices.
Wally K wrote:
> What motors are you running that give you 1200 oz-in, steppers or
> servos.
>
> Wally K.
>
> --- In CAD_CAM_EDM_DRO@egroups.com, "Carey L. Culpepper" <mr.c@b...>
> wrote:
> > Hugh: I am currently running 3/4" "L" series belts with 12 tooth
> and 24 tooth pulleys. Even the knee feed(z axis) has a 3/4" belt.
> > This one really should be a 1" belt but I was having trouble
> finding a 12 tooth in 1" . So I will use a 1" 14 and 28 tooth pulley
> on
> > the knee. My motors are about 1200 oz. in.. I was drilling some
> very big holes with the x axis(angle head) and had no problems. One
> > drill pass was from 1" to 1 3/4" . The program went haywire and
> went rapid feed into the piece. It just pushed it down the table. It
> > was a piece of cold rolled clamped very tightly to the table.
> > Those big pulleys would be overkill. Particularly with only 785 oz.
> in. I will try to find a 1" kevlar belt for the knee at some
> > point since it is pushing a good bit of iron up and the kevlar
> won't stretch as much. I hope that this helps, Carey.
> >
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator]
> URL to this page: http://www.egroups.com/group/CAD_CAM_EDM_DRO
> FAQ: http://www.ktmarketing.com/faq.html
> bill,
> List Manager
Discussion Thread
Jon Elson
2000-11-24 22:16:09 UTC
Re: Clifton motors
Wally K
2000-11-25 04:18:25 UTC
wrong guy, but have servo question.
r_fl_z@h...
2000-11-25 14:27:06 UTC
Re: wrong guy, but have servo question.
Wally K
2000-11-25 14:46:31 UTC
Re: wrong guy, but have servo question.
r_fl_z@h...
2000-11-25 14:52:28 UTC
Re: Clifton motors
Mariss Freimanis
2000-11-25 20:13:18 UTC
Re: wrong guy, but have servo question.
Jon Elson
2000-11-25 20:49:14 UTC
Re: [CAD_CAM_EDM_DRO] wrong guy, but have servo question.
Jon Elson
2000-11-25 21:25:43 UTC
Re: [CAD_CAM_EDM_DRO] Re: wrong guy, but have servo question.
Jon Elson
2000-11-25 21:30:04 UTC
Re: [CAD_CAM_EDM_DRO] Re: Clifton motors
Wally K
2000-11-25 23:37:43 UTC
Re: wrong guy, but have servo question.
Wally K
2000-11-25 23:59:51 UTC
Servo questions.
Jon Elson
2000-11-27 00:06:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: wrong guy, but have servo question.
Jon Elson
2000-11-27 00:10:47 UTC
Re: [CAD_CAM_EDM_DRO] Servo questions.
Wally K
2000-11-27 06:06:32 UTC
Re: wrong guy, but have servo question.
Carey L. Culpepper
2000-11-27 06:28:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: wrong guy, but have servo question.
Wally K
2000-11-27 06:38:09 UTC
Re: wrong guy, but have servo question.
Marcus & Eva
2000-11-27 07:58:46 UTC
Re: [CAD_CAM_EDM_DRO] Re: wrong guy, but have servo question.
Wally K
2000-11-27 10:18:11 UTC
Z axis conversion
Hugh Currin
2000-11-27 11:44:06 UTC
Re: Z axis conversion
Wally K
2000-11-27 12:14:10 UTC
Re: Z axis conversion
Hugh Currin
2000-11-27 12:49:15 UTC
Re: Z axis conversion
Wally K
2000-11-27 13:01:34 UTC
Re: Z axis conversion
JanRwl@A...
2000-11-27 14:34:36 UTC
Re: [CAD_CAM_EDM_DRO] Re: wrong guy, but have servo question.
Hugh Currin
2000-11-27 15:31:22 UTC
Stepper Motor Wiring ?
Hugh Currin
2000-11-27 15:31:23 UTC
Timing Belt Sizing
Hugh Currin
2000-11-27 15:31:26 UTC
Electronic Box Shielding ?
JanRwl@A...
2000-11-27 16:13:01 UTC
Re: [CAD_CAM_EDM_DRO] Electronic Box Shielding ?
Jon Elson
2000-11-27 16:33:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: wrong guy, but have servo question.
Jon Elson
2000-11-27 16:40:17 UTC
Re: [CAD_CAM_EDM_DRO] Timing Belt Sizing
Jon Elson
2000-11-27 16:42:43 UTC
Re: [CAD_CAM_EDM_DRO] Electronic Box Shielding ?
Tim Goldstein
2000-11-27 16:56:54 UTC
RE: [CAD_CAM_EDM_DRO] Stepper Motor Wiring ?
Wally K
2000-11-27 17:01:25 UTC
Re: Stepper Motor Wiring ?
Mariss Freimanis
2000-11-27 17:17:48 UTC
Re: Electronic Box Shielding ?
Wally K
2000-11-27 17:32:57 UTC
Re: Timing Belt Sizing
Wally K
2000-11-27 17:43:27 UTC
Re: Timing Belt Sizing
Carey L. Culpepper
2000-11-27 17:52:41 UTC
Re: [CAD_CAM_EDM_DRO] Timing Belt Sizing
Wally K
2000-11-27 18:04:22 UTC
Re: Electronic Box Shielding ?
Wally K
2000-11-27 18:24:49 UTC
Re: Timing Belt Sizing
Carey L. Culpepper
2000-11-27 18:46:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: Timing Belt Sizing
Marcus & Eva
2000-11-27 19:10:53 UTC
Re: [CAD_CAM_EDM_DRO] Re: wrong guy, but have servo question.
Hugh Currin
2000-11-27 20:28:17 UTC
Re: Electronic Box Shielding ?
JanRwl@A...
2000-11-27 20:37:38 UTC
Re: [CAD_CAM_EDM_DRO] Stepper Motor Wiring ?
JanRwl@A...
2000-11-27 20:41:36 UTC
Re: [CAD_CAM_EDM_DRO] Timing Belt Sizing
Mariss Freimanis
2000-11-27 20:59:39 UTC
Re: Electronic Box Shielding ?
Jon Elson
2000-11-27 23:00:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: wrong guy, but have servo question.
Jon Elson
2000-11-27 23:10:42 UTC
Re: [CAD_CAM_EDM_DRO] Timing Belt Sizing
Wally K
2000-11-28 01:02:30 UTC
What is a head knuckle
ballendo@y...
2000-11-28 01:23:52 UTC
re:What is a head knuckle
Smoke
2000-11-28 01:51:19 UTC
Re: [CAD_CAM_EDM_DRO] re:What is a head knuckle
ptengin@a...
2000-11-28 02:17:25 UTC
Re: [CAD_CAM_EDM_DRO] Timing Belt Sizing
Marcus & Eva
2000-11-28 07:40:47 UTC
Re: [CAD_CAM_EDM_DRO] Re: wrong guy, but have servo question.
dave engvall
2000-11-28 08:11:07 UTC
Re: [CAD_CAM_EDM_DRO] Re: wrong guy, but have servo question.
Smoke
2000-11-28 10:25:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: wrong guy, but have servo question.
Jon Elson
2000-11-28 12:30:19 UTC
Re: [CAD_CAM_EDM_DRO] What is a head knuckle
Jon Elson
2000-11-28 12:51:01 UTC
Re: [CAD_CAM_EDM_DRO] Re: wrong guy, but have servo question.
ballendo@y...
2000-11-28 14:09:22 UTC
Re: Re: wrong guy, but have servo question.
ptengin@a...
2000-11-28 15:22:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: wrong guy, but have servo question.
dave engvall
2000-11-28 20:01:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: wrong guy, but have servo question.
Marcus & Eva
2000-11-28 21:49:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: wrong guy, but have servo question.
Doug Harrison
2000-11-29 16:23:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Timing Belt Sizing
Wally K
2000-11-29 17:15:04 UTC
Re: Timing Belt Sizing
ballendo@y...
2000-11-29 18:23:42 UTC
Re: Re: Timing Belt Sizing
Jon Elson
2000-11-29 21:56:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: Timing Belt Sizing
no falloff
2002-07-22 07:25:34 UTC
Servo questions.
Jon Elson
2002-07-22 10:07:42 UTC
Re: [CAD_CAM_EDM_DRO] Servo questions.
Peter Seddon
2002-07-22 10:15:18 UTC
Re: [CAD_CAM_EDM_DRO] Servo questions.