Re: [CAD_CAM_EDM_DRO] What is everyone doing, building, wanting to learn?
Posted by
Garry and Maxine
on 2001-01-06 16:24:12 UTC
To: CAD_CAM_EDM_DRO@egroups.com
From: wanliker@...
Date sent: Sat, 6 Jan 2001 18:14:15 EST
Send reply to: CAD_CAM_EDM_DRO@egroups.com
Subject: Re: [CAD_CAM_EDM_DRO] What is everyone doing, building, wanting to learn?
something I hadn't thought of. Makes the spring much more feasible.
Your unit with an encoder should do very nicely.
Have you seen the BW electronics units I am talking about. John
(from the Uk) has said nice things about them. The idea seems more
sound than the pulley sliding along the wire to me. However as no
one else has jumped on it it makes me wonder. Do they see faults I
don't?
Do you remember if the unit used a wire spring or a flat ribbon
spring. Was there a guide to keep the wire spooling with out over
laps or did the tension take care of that.
Also is very thin aircraft cable in the .050 range or the .100 range?
Thanks !
Garry
From: wanliker@...
Date sent: Sat, 6 Jan 2001 18:14:15 EST
Send reply to: CAD_CAM_EDM_DRO@egroups.com
Subject: Re: [CAD_CAM_EDM_DRO] What is everyone doing, building, wanting to learn?
> In a message dated 1/6/01 1:00:13 PM Mountain Standard Time,Bill This is starting to give me a clue.....The hollow pulley was
> gmfoster@... writes:
>
>I even considered ordering one of their systems. However the
>shipping makes it rather expensive for something I can't see first.
> >>
> We used a similar set up on a pan positioning machine in the bread
> making business. The pully was hollow with a central shaft, it had a
> spring wound up inside of it, and the outside of the pully had flanges
> on both sides, the cable, very thin aircraft cable was wound around
> the outside, It turned a 10 turn pot., it was fastened to the center
> shaft of the pully. And according to the software we were reading
> .001 inch. The software also set the start point and the end point
> for measuring. I can probably find out more if desired, the unit was
> less than 2" square. The travel was about 6-7 feet bill
something I hadn't thought of. Makes the spring much more feasible.
Your unit with an encoder should do very nicely.
Have you seen the BW electronics units I am talking about. John
(from the Uk) has said nice things about them. The idea seems more
sound than the pulley sliding along the wire to me. However as no
one else has jumped on it it makes me wonder. Do they see faults I
don't?
Do you remember if the unit used a wire spring or a flat ribbon
spring. Was there a guide to keep the wire spooling with out over
laps or did the tension take care of that.
Also is very thin aircraft cable in the .050 range or the .100 range?
Thanks !
Garry
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
> discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@egroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@egroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@egroups.com
> List owner: CAD_CAM_EDM_DRO-owner@egroups.com, wanliker@...
> Moderator: jmelson@... [Moderator] URL to this page:
> http://www.egroups.com/group/CAD_CAM_EDM_DRO FAQ:
> http://www.ktmarketing.com/faq.html bill, List Manager
>
Discussion Thread
Alan Marconett KM6VV
2001-01-04 11:51:05 UTC
Re: Digitizers, Renishaw
PMeinhard@a...
2001-01-04 13:37:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
Fred Smith
2001-01-04 14:40:26 UTC
Re: Digitizers, Renishaw
Alan Marconett KM6VV
2001-01-04 15:32:53 UTC
Re: Digitizers, Renishaw
Smoke
2001-01-04 15:44:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
Alan Marconett KM6VV
2001-01-04 15:47:26 UTC
Re: Digitizers, Renishaw
Alan Marconett KM6VV
2001-01-04 15:55:33 UTC
Re: Digitizers, Renishaw
Fred Smith
2001-01-04 16:07:56 UTC
Re: Digitizers, Renishaw
Ian Wright
2001-01-04 16:35:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
dave engvall
2001-01-04 17:17:39 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
dougrasmussen@c...
2001-01-04 18:16:20 UTC
Re: Digitizers, Renishaw
Alan Marconett KM6VV
2001-01-04 18:39:08 UTC
Re: Digitizers, Renishaw
Alan Marconett KM6VV
2001-01-04 18:47:22 UTC
Re: Digitizers, Renishaw
Fred Smith
2001-01-04 19:10:16 UTC
Re: Digitizers, Renishaw
Greg Nuspel
2001-01-04 19:18:08 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
Alan Marconett KM6VV
2001-01-04 20:48:51 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
Smoke
2001-01-04 21:16:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
Smoke
2001-01-04 21:27:16 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
Jon Elson
2001-01-04 22:26:59 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
PMeinhard@a...
2001-01-05 03:53:03 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
Ian Wright
2001-01-05 13:02:22 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
Alan Marconett KM6VV
2001-01-05 14:16:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
Bill Phillips
2001-01-05 14:27:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
ballendo@y...
2001-01-05 15:01:44 UTC
Re: Re: Digitizers, Renishaw
ballendo@y...
2001-01-05 15:06:31 UTC
re:Re: Digitizers, Renishaw
ballendo@y...
2001-01-05 15:20:52 UTC
Re: Re: Digitizers, Renishaw
PMeinhard@a...
2001-01-05 15:34:13 UTC
Digitizers, Renishaw
Smoke
2001-01-05 15:44:18 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: Digitizers, Renishaw
Alan Marconett KM6VV
2001-01-05 15:45:45 UTC
Re: Digitizers, Renishaw
Alan Marconett KM6VV
2001-01-05 15:50:07 UTC
Re: Digitizers, Renishaw
ballendo@y...
2001-01-05 15:55:04 UTC
Re: Digitizers, Renishaw
ballendo@y...
2001-01-05 16:51:51 UTC
Re: Re: Digitizers, Renishaw
Alan Marconett KM6VV
2001-01-05 18:29:57 UTC
Re: Digitizers, Renishaw
Jeff Demand
2001-01-05 18:32:11 UTC
Re: [CAD_CAM_EDM_DRO] Re: Re: Digitizers, Renishaw
Tim Goldstein
2001-01-05 19:12:09 UTC
What is everyone doing, building, wanting to learn?
wanliker@a...
2001-01-05 20:06:43 UTC
Re: [CAD_CAM_EDM_DRO] What is everyone doing, building, wanting to learn?
JanRwl@A...
2001-01-05 20:12:16 UTC
Re: [CAD_CAM_EDM_DRO] What is everyone doing, building, wanting to learn?
Jon Elson
2001-01-05 22:42:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
Garry and Maxine
2001-01-06 11:55:25 UTC
Re: [CAD_CAM_EDM_DRO] What is everyone doing, building, wanting to learn?
ballendo@y...
2001-01-06 13:30:16 UTC
re:RE: Re: Digitizers, Renishaw
Tim Goldstein
2001-01-06 13:31:06 UTC
RE: [CAD_CAM_EDM_DRO] What is everyone doing, building, wanting to learn?
ballendo@y...
2001-01-06 13:55:21 UTC
Re: Re: Digitizers, Renishaw
Bill Phillips
2001-01-06 14:04:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
Bill Phillips
2001-01-06 14:04:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
Bill Phillips
2001-01-06 14:04:26 UTC
Re: [CAD_CAM_EDM_DRO] Digitizers, Renishaw
Garry and Maxine
2001-01-06 14:52:25 UTC
RE: [CAD_CAM_EDM_DRO] What is everyone doing, building, wanting to learn?
Greg Nuspel
2001-01-06 14:59:51 UTC
Re: [CAD_CAM_EDM_DRO] Digitizers, Renishaw
Greg Nuspel
2001-01-06 15:03:00 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
wanliker@a...
2001-01-06 15:14:58 UTC
Re: [CAD_CAM_EDM_DRO] What is everyone doing, building, wanting to learn?
wally daniels
2001-01-06 15:38:45 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
Garry and Maxine
2001-01-06 16:24:12 UTC
Re: [CAD_CAM_EDM_DRO] What is everyone doing, building, wanting to learn?
Garry and Maxine
2001-01-06 16:27:39 UTC
Re: [CAD_CAM_EDM_DRO] What is everyone doing, building, wanting to learn?
Alan Marconett KM6VV
2001-01-06 16:34:05 UTC
Re: Digitizers, Renishaw
ballendo@y...
2001-01-06 18:05:33 UTC
re:Re: Digitizers, Renishaw
wanliker@a...
2001-01-06 19:52:07 UTC
Re: [CAD_CAM_EDM_DRO] What is everyone doing, building, wanting to learn?
Al Lenz
2001-01-06 21:05:32 UTC
re:Re: Digitizers, Renishaw
Garry and Maxine
2001-01-06 21:09:41 UTC
Re: [CAD_CAM_EDM_DRO] What is everyone doing, building, wanting to learn?
Alan Marconett KM6VV
2001-01-06 21:58:01 UTC
Re: Digitizers, Renishaw
Smoke
2001-01-06 22:00:38 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
ballendo@y...
2001-01-06 23:40:11 UTC
re:re:Re: Digitizers, Renishaw
ballendo@y...
2001-01-07 01:09:34 UTC
re:Re: Digitizers, Renishaw
PMeinhard@a...
2001-01-07 01:34:48 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
Ian Wright
2001-01-07 02:35:26 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
Jeff Demand
2001-01-07 08:10:16 UTC
Re: [CAD_CAM_EDM_DRO] What is everyone doing, building, wanting to learn?
Charli
2001-01-07 11:07:33 UTC
RE: [CAD_CAM_EDM_DRO] What is everyone doing, building, wanting to learn?
gmaithonis@y...
2001-01-07 11:17:28 UTC
Re: What is everyone doing, building, wanting to learn?
Tim Goldstein
2001-01-07 11:26:27 UTC
RE: [CAD_CAM_EDM_DRO] What is everyone doing, building, wanting to learn?
Jon Anderson
2001-01-07 11:29:34 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
Tim Goldstein
2001-01-07 11:31:54 UTC
RE: [CAD_CAM_EDM_DRO] Re: What is everyone doing, building, wanting to learn?
Bill Phillips
2001-01-07 13:58:20 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
Marcus & Eva
2001-01-08 08:05:28 UTC
Re: [CAD_CAM_EDM_DRO] Re: What is everyone doing, building, wanting to learn?
Drew Rogge
2001-01-08 08:18:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
Alan Marconett KM6VV
2001-01-08 11:29:26 UTC
Re: Digitizers, Renishaw
gmaithonis@y...
2001-01-08 16:46:08 UTC
Re: What is everyone doing, building, wanting to learn?
ballendo@y...
2001-01-08 17:21:34 UTC
re:Re: Digitizers, Renishaw
Alan Marconett KM6VV
2001-01-09 00:25:56 UTC
Re: Digitizers, Renishaw
Ian Wright
2001-01-09 02:03:56 UTC
Re: [CAD_CAM_EDM_DRO] re:Re: Digitizers, Renishaw
Roman Black
2001-01-09 02:45:33 UTC
Re: Digitizers, Renishaw
John Wettroth
2001-01-09 09:25:12 UTC
RE: What is everyone doing, building, wanting to learn?
Alan Marconett KM6VV
2001-01-09 10:26:45 UTC
Re: Digitizers, Renishaw
Bruce
2001-01-09 15:56:41 UTC
Re: What is everyone doing, building, wanting to learn?
John D. Guenther
2001-01-10 09:49:42 UTC
Re: What is everyone doing, building, wanting to learn?
Jon Elson
2001-01-10 22:45:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
Roman Black
2001-01-11 11:39:15 UTC
Re: Digitizers, Renishaw
Jon Elson
2001-01-11 12:02:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
Alan Marconett KM6VV
2001-01-11 12:33:11 UTC
Re: Digitizers, Renishaw
ballendo@y...
2001-01-11 12:58:57 UTC
re:Re: What is everyone doing, building, wanting to learn?
John D. Guenther
2001-01-11 13:31:18 UTC
re:Re: What is everyone doing, building, wanting to learn?
Ian Wright
2001-01-11 15:17:50 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
Marcus & Eva
2001-01-11 21:30:37 UTC
Re: [CAD_CAM_EDM_DRO] re:Re: What is everyone doing, building, wanting to learn?
Smoke
2001-01-11 21:45:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
Ian Wright
2001-01-12 02:47:13 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
Roman Black
2001-01-12 05:24:23 UTC
Re: Digitizers, Renishaw
Roman Black
2001-01-12 06:23:38 UTC
Re: Digitizers, Renishaw
Jon Anderson
2001-01-12 08:02:09 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
Smoke
2001-01-12 09:29:33 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
Jon Elson
2001-01-12 11:51:15 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
Smoke
2001-01-12 12:25:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
Ian Wright
2001-01-12 13:47:57 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
Smoke
2001-01-12 14:24:14 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
ballendo@y...
2001-01-12 19:03:48 UTC
re:Re: Digitizers, Renishaw
ballendo@y...
2001-01-12 19:21:45 UTC
re:Re: Digitizers, Renishaw
Jon Anderson
2001-01-12 19:28:06 UTC
Re: [CAD_CAM_EDM_DRO] re:Re: Digitizers, Renishaw
ballendo@y...
2001-01-12 21:35:53 UTC
Re: re:Re: Digitizers, Renishaw
dave engvall
2001-01-14 08:58:02 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
Smoke
2001-08-13 15:49:05 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
Jon Elson
2001-08-13 23:08:24 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
Bill McGown
2001-08-14 06:03:41 UTC
Re: Digitizers, Renishaw
Smoke
2001-08-14 07:03:38 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw
diazden
2001-08-14 08:17:23 UTC
Re: [CAD_CAM_EDM_DRO] Re: Digitizers, Renishaw