Re: [CAD_CAM_EDM_DRO] Using wood router on aluminum
Posted by
Bob Campbell
on 2001-05-15 13:04:04 UTC
Vic,
I cut aluminum parts all the time on my cnc router. Aluminum can be cut
with carbide bits and high speeds. I am using a Porter Cable 5 speed 3.25
hp router and I run it at about 21,000 rpm. For deep cuts, I cut each pass
about .1 inches deep.
Bob Campbell
I cut aluminum parts all the time on my cnc router. Aluminum can be cut
with carbide bits and high speeds. I am using a Porter Cable 5 speed 3.25
hp router and I run it at about 21,000 rpm. For deep cuts, I cut each pass
about .1 inches deep.
Bob Campbell
----- Original Message -----
From: "Vic Fraenckel" <vfraenc1@...>
To: "CAD_CAM_EDM_DRO Maillist" <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Tuesday, May 15, 2001 1:56 PM
Subject: [CAD_CAM_EDM_DRO] Using wood router on aluminum
> Is it possible to mill openings in aluminum panels using a wood router? If
> so, are there cutters available to use with the router?
>
> Any advice or comments appreciated.
>
> Vic
> ________________________________________________________
>
> Victor Fraenckel - The Windman vfraenc1@...
> KC2GUI
www.windsway.com
>
> Home of the WindReader Electronic Theodolite
> Read the WIND
>
>
>
> Welcome to CAD_CAM_EDM_DRO@...,an unmoderated list for the
discussion of shop built systems, for CAD, CAM, EDM, and DRO.
>
> Addresses:
> Post message: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
> FAQ: http://www.ktmarketing.com/faq.html
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
Discussion Thread
Vic Fraenckel
2001-05-15 11:55:16 UTC
Using wood router on aluminum
cadman@p...
2001-05-15 12:06:26 UTC
Re: Using wood router on aluminum
Joe Vicars
2001-05-15 12:18:44 UTC
Re: [CAD_CAM_EDM_DRO] Re: Using wood router on aluminum
Bob Campbell
2001-05-15 13:04:04 UTC
Re: [CAD_CAM_EDM_DRO] Using wood router on aluminum
jguenther@l...
2001-05-15 13:17:03 UTC
Re: Using wood router on aluminum
Bob Campbell
2001-05-15 13:48:49 UTC
Re: [CAD_CAM_EDM_DRO] Re: Using wood router on aluminum
JanRwl@A...
2001-05-15 15:11:33 UTC
Re: [CAD_CAM_EDM_DRO] Using wood router on aluminum
JanRwl@A...
2001-05-15 15:19:10 UTC
Re: [CAD_CAM_EDM_DRO] Re: Using wood router on aluminum
Bob Campbell
2001-05-15 17:39:57 UTC
Re: [CAD_CAM_EDM_DRO] Using wood router on aluminum
ballendo@y...
2001-05-15 19:28:12 UTC
Re: Using wood router on aluminum
ballendo@y...
2001-05-15 19:38:17 UTC
Re: Using wood router on aluminum
ballendo@y...
2001-05-15 20:22:06 UTC
Re: Using wood router on aluminum
yahoo@a...
2001-05-16 05:18:32 UTC
Re: Using wood router on aluminum
rab@r...
2001-05-16 08:00:56 UTC
Re: Using wood router on aluminum
ballendo@y...
2001-05-21 17:21:07 UTC
Re: Using wood router on aluminum