Re: [CAD_CAM_EDM_DRO] Motor Noise?
Posted by
Sven Peter, TAD S.A.
on 2001-06-21 20:26:11 UTC
Where can you get ferrite beads or how can you make them.
I have an application where I fear to get 1,5 MHz radiation into
the mini PLC. I haven't seen ferrite beads for years and have no
supplier for them. (asked already all local electric and electronic suppliers)
Any answer is very appreciated.
Thanks
Sven Peter
Alan Marconett KM6VV wrote:
I have an application where I fear to get 1,5 MHz radiation into
the mini PLC. I haven't seen ferrite beads for years and have no
supplier for them. (asked already all local electric and electronic suppliers)
Any answer is very appreciated.
Thanks
Sven Peter
Alan Marconett KM6VV wrote:
> Hi Phil,[Non-text portions of this message have been removed]
>
> You might try some of the "clamp-on" ferrite cores used for computer
> cables. At the speed control, at the computer parallel port cable, at
> the driver, etc.
>
> Alan KM6VV
>
> phil wrote:
> >
> > I'm using a router speed control with a small laminate style trimmer and since installing the speed controller I've got problems on my Z Axis with lost steps.
> >
> > If I remove the speed control then all works well.
> >
> > Any suggestions on how best to -
> >
> > a) reduce the noise from the speed controller and/or motor
> > b) shield the steppers from the noise.
> >
> > thanks!
> >
> > Phil
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
Discussion Thread
phil
2001-06-21 17:48:03 UTC
Motor Noise?
cncdxf@a...
2001-06-21 18:09:11 UTC
Re: Motor Noise?
phil
2001-06-21 19:23:31 UTC
Re: [CAD_CAM_EDM_DRO] Re: Motor Noise?
cncdxf@a...
2001-06-21 19:44:22 UTC
Re: Motor Noise?
Alan Marconett KM6VV
2001-06-21 20:02:12 UTC
Re: [CAD_CAM_EDM_DRO] Motor Noise?
Sven Peter, TAD S.A.
2001-06-21 20:21:12 UTC
Re: [CAD_CAM_EDM_DRO] Re: Motor Noise?
Sven Peter, TAD S.A.
2001-06-21 20:26:11 UTC
Re: [CAD_CAM_EDM_DRO] Motor Noise?
Jon Elson
2001-06-21 21:21:18 UTC
Re: [CAD_CAM_EDM_DRO] Motor Noise?
Alan Marconett KM6VV
2001-06-22 00:22:27 UTC
Re: [CAD_CAM_EDM_DRO] Motor Noise?
phil
2001-06-22 12:23:41 UTC
Re: [CAD_CAM_EDM_DRO] Motor Noise?
Rich D.
2001-06-22 12:55:12 UTC
Re: [CAD_CAM_EDM_DRO] Motor Noise?
cncdxf@a...
2001-06-22 17:44:30 UTC
Re: Motor Noise?
Alan Marconett KM6VV
2001-06-22 18:17:15 UTC
Re: [CAD_CAM_EDM_DRO] Motor Noise?
Alan Marconett KM6VV
2001-06-22 19:05:29 UTC
Re: Motor Noise?
phil
2001-06-22 19:44:35 UTC
Re: [CAD_CAM_EDM_DRO] Motor Noise?
Sven Peter, TAD S.A.
2001-06-23 07:35:58 UTC
Re: [CAD_CAM_EDM_DRO] Motor Noise?
Alan Marconett KM6VV
2001-06-23 12:09:47 UTC
Re: [CAD_CAM_EDM_DRO] Motor Noise?
Sven Peter, TAD S.A.
2001-06-23 22:07:13 UTC
Re: [CAD_CAM_EDM_DRO] Motor Noise?
Alan Marconett KM6VV
2001-06-24 14:30:19 UTC
Re: [CAD_CAM_EDM_DRO] Motor Noise?
Sven Peter, TAD S.A.
2001-06-24 17:05:37 UTC
Re: [CAD_CAM_EDM_DRO] Motor Noise?
Alan Marconett KM6VV
2001-06-24 18:10:36 UTC
Re: [CAD_CAM_EDM_DRO] Motor Noise?
ptengin@a...
2001-06-25 20:03:45 UTC
Re: [CAD_CAM_EDM_DRO] Motor Noise?
Alan Marconett KM6VV
2001-06-25 20:09:04 UTC
Re: [CAD_CAM_EDM_DRO] Motor Noise?
Sven Peter, TAD S.A.
2001-06-25 20:47:51 UTC
Re: [CAD_CAM_EDM_DRO] Motor Noise?
Alan Marconett KM6VV
2001-06-25 22:09:30 UTC
Re: [CAD_CAM_EDM_DRO] Motor Noise?
Sven Peter, TAD S.A.
2001-06-26 21:40:27 UTC
Re: [CAD_CAM_EDM_DRO] Motor Noise?
Alan Marconett KM6VV
2001-06-27 10:30:10 UTC
Re: [CAD_CAM_EDM_DRO] Motor Noise?
Sven Peter, TAD S.A.
2001-06-27 21:39:00 UTC
Re: [CAD_CAM_EDM_DRO] Motor Noise?
Alan Marconett KM6VV
2001-06-28 10:44:15 UTC
Re: [CAD_CAM_EDM_DRO] Motor Noise?
Sven Peter, TAD S.A.
2001-06-28 20:33:29 UTC
Re: [CAD_CAM_EDM_DRO] Motor Noise?
Alan Marconett KM6VV
2001-06-28 23:33:13 UTC
Re: [CAD_CAM_EDM_DRO] Motor Noise?
Sven Peter, TAD S.A.
2001-06-29 06:53:24 UTC
Re: [CAD_CAM_EDM_DRO] Motor Noise?