CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Motor Noise?

Posted by phil
on 2001-06-22 12:23:41 UTC
Alan,

I was thinking about trying these but didn't know where to buy them. Any
ideas on suppliers of these ?

thanks

Phil
----- Original Message -----
From: "Alan Marconett KM6VV" <KM6VV@...>
To: <CAD_CAM_EDM_DRO@yahoogroups.com>
Sent: Thursday, June 21, 2001 11:03 PM
Subject: Re: [CAD_CAM_EDM_DRO] Motor Noise?


> Hi Phil,
>
> You might try some of the "clamp-on" ferrite cores used for computer
> cables. At the speed control, at the computer parallel port cable, at
> the driver, etc.
>
> Alan KM6VV
>
> phil wrote:
> >
> > I'm using a router speed control with a small laminate style trimmer
and since installing the speed controller I've got problems on my Z Axis
with lost steps.
> >
> > If I remove the speed control then all works well.
> >
> > Any suggestions on how best to -
> >
> > a) reduce the noise from the speed controller and/or motor
> > b) shield the steppers from the noise.
> >
> > thanks!
> >
> > Phil
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>

Discussion Thread

phil 2001-06-21 17:48:03 UTC Motor Noise? cncdxf@a... 2001-06-21 18:09:11 UTC Re: Motor Noise? phil 2001-06-21 19:23:31 UTC Re: [CAD_CAM_EDM_DRO] Re: Motor Noise? cncdxf@a... 2001-06-21 19:44:22 UTC Re: Motor Noise? Alan Marconett KM6VV 2001-06-21 20:02:12 UTC Re: [CAD_CAM_EDM_DRO] Motor Noise? Sven Peter, TAD S.A. 2001-06-21 20:21:12 UTC Re: [CAD_CAM_EDM_DRO] Re: Motor Noise? Sven Peter, TAD S.A. 2001-06-21 20:26:11 UTC Re: [CAD_CAM_EDM_DRO] Motor Noise? Jon Elson 2001-06-21 21:21:18 UTC Re: [CAD_CAM_EDM_DRO] Motor Noise? Alan Marconett KM6VV 2001-06-22 00:22:27 UTC Re: [CAD_CAM_EDM_DRO] Motor Noise? phil 2001-06-22 12:23:41 UTC Re: [CAD_CAM_EDM_DRO] Motor Noise? Rich D. 2001-06-22 12:55:12 UTC Re: [CAD_CAM_EDM_DRO] Motor Noise? cncdxf@a... 2001-06-22 17:44:30 UTC Re: Motor Noise? Alan Marconett KM6VV 2001-06-22 18:17:15 UTC Re: [CAD_CAM_EDM_DRO] Motor Noise? Alan Marconett KM6VV 2001-06-22 19:05:29 UTC Re: Motor Noise? phil 2001-06-22 19:44:35 UTC Re: [CAD_CAM_EDM_DRO] Motor Noise? Sven Peter, TAD S.A. 2001-06-23 07:35:58 UTC Re: [CAD_CAM_EDM_DRO] Motor Noise? Alan Marconett KM6VV 2001-06-23 12:09:47 UTC Re: [CAD_CAM_EDM_DRO] Motor Noise? Sven Peter, TAD S.A. 2001-06-23 22:07:13 UTC Re: [CAD_CAM_EDM_DRO] Motor Noise? Alan Marconett KM6VV 2001-06-24 14:30:19 UTC Re: [CAD_CAM_EDM_DRO] Motor Noise? Sven Peter, TAD S.A. 2001-06-24 17:05:37 UTC Re: [CAD_CAM_EDM_DRO] Motor Noise? Alan Marconett KM6VV 2001-06-24 18:10:36 UTC Re: [CAD_CAM_EDM_DRO] Motor Noise? ptengin@a... 2001-06-25 20:03:45 UTC Re: [CAD_CAM_EDM_DRO] Motor Noise? Alan Marconett KM6VV 2001-06-25 20:09:04 UTC Re: [CAD_CAM_EDM_DRO] Motor Noise? Sven Peter, TAD S.A. 2001-06-25 20:47:51 UTC Re: [CAD_CAM_EDM_DRO] Motor Noise? Alan Marconett KM6VV 2001-06-25 22:09:30 UTC Re: [CAD_CAM_EDM_DRO] Motor Noise? Sven Peter, TAD S.A. 2001-06-26 21:40:27 UTC Re: [CAD_CAM_EDM_DRO] Motor Noise? Alan Marconett KM6VV 2001-06-27 10:30:10 UTC Re: [CAD_CAM_EDM_DRO] Motor Noise? Sven Peter, TAD S.A. 2001-06-27 21:39:00 UTC Re: [CAD_CAM_EDM_DRO] Motor Noise? Alan Marconett KM6VV 2001-06-28 10:44:15 UTC Re: [CAD_CAM_EDM_DRO] Motor Noise? Sven Peter, TAD S.A. 2001-06-28 20:33:29 UTC Re: [CAD_CAM_EDM_DRO] Motor Noise? Alan Marconett KM6VV 2001-06-28 23:33:13 UTC Re: [CAD_CAM_EDM_DRO] Motor Noise? Sven Peter, TAD S.A. 2001-06-29 06:53:24 UTC Re: [CAD_CAM_EDM_DRO] Motor Noise?