CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Interface options, headless boxen, and remote control ...

Posted by Bryan-TheBS-Smith
on 2001-08-19 16:56:14 UTC
Jon Elson wrote:
> But, you DON'T NEED more than one port. You can VERY easily address
> up to 256 device registers with one parallel port. I have pretty much
> broken it up so each board gets 8 consecutive addresses. That allows
> up to 8 boards to be plugged into one bus.

Which is good for systems that have a parallel port. But we're
staring to see these "legacy free" systems come about without one.

-- TheBS

--
Bryan "TheBS" Smith mailto:b.j.smith@... chat:thebs413
Engineer Absolute Value Systems, Inc. http://www.linux-wlan.org
President SmithConcepts, Inc. http://www.SmithConcepts.com

Discussion Thread

Bryan-TheBS-Smith 2001-08-18 20:33:52 UTC Interface options, headless boxen, and remote control ... Weyland 2001-08-18 21:20:37 UTC Re: [CAD_CAM_EDM_DRO] Interface options, headless boxen, and remote control ... Bryan-TheBS-Smith 2001-08-18 21:47:16 UTC Re: [CAD_CAM_EDM_DRO] Interface options, headless boxen, and remote control ... Jon Elson 2001-08-18 23:00:13 UTC Re: [CAD_CAM_EDM_DRO] Interface options, headless boxen, and remote control ... Jon Elson 2001-08-18 23:17:21 UTC Re: [CAD_CAM_EDM_DRO] Interface options, headless boxen, and remote control ... Ian Wright 2001-08-19 02:16:51 UTC Re: [CAD_CAM_EDM_DRO] Interface options, headless boxen, and remote control ... Wally Daniels 2001-08-19 03:57:53 UTC Re: [CAD_CAM_EDM_DRO] Interface options, headless boxen, and remote control ... Bryan-TheBS-Smith 2001-08-19 05:26:34 UTC Re: [CAD_CAM_EDM_DRO] Interface options, headless boxen, and remote control ... Bryan-TheBS-Smith 2001-08-19 05:30:43 UTC Re: [CAD_CAM_EDM_DRO] Interface options, headless boxen, and remote control ... Bryan-TheBS-Smith 2001-08-19 05:53:52 UTC Re: [CAD_CAM_EDM_DRO] Interface options, headless boxen, and remote control ... Bryan-TheBS-Smith 2001-08-19 06:07:39 UTC [CAD_CAM_EDM_DRO] Interface options, headless boxen, and remote control ... Larry Edington 2001-08-19 06:12:07 UTC Re: [CAD_CAM_EDM_DRO] Interface options, headless boxen, and remote control ... Larry Edington 2001-08-19 06:14:56 UTC Re: [CAD_CAM_EDM_DRO] Interface options, headless boxen, and remote control ... Bryan-TheBS-Smith 2001-08-19 06:29:46 UTC Re: [CAD_CAM_EDM_DRO] Interface options, headless boxen, and remote control ... Bryan-TheBS-Smith 2001-08-19 06:30:51 UTC Re: [CAD_CAM_EDM_DRO] Interface options, headless boxen, and remote control ... William Scalione 2001-08-19 09:13:18 UTC Re: [CAD_CAM_EDM_DRO] Interface options, headless boxen, and remote control ... Larry Edington 2001-08-19 09:28:36 UTC Re: [CAD_CAM_EDM_DRO] Interface options, headless boxen, and remote control ... Carlos Guillermo 2001-08-19 09:46:57 UTC RE: [CAD_CAM_EDM_DRO] Interface options, headless boxen, and remote control ... Larry Edington 2001-08-19 10:08:24 UTC Re: [CAD_CAM_EDM_DRO] Interface options, headless boxen, and remote control ... Bryan-TheBS-Smith 2001-08-19 10:31:59 UTC Re: [CAD_CAM_EDM_DRO] Interface options, headless boxen, and remote control ... Carol & Jerry Jankura 2001-08-19 10:42:37 UTC RE: [CAD_CAM_EDM_DRO] Interface options, headless boxen, and remote control ... Carol & Jerry Jankura 2001-08-19 10:45:51 UTC RE: [CAD_CAM_EDM_DRO] Interface options, headless boxen, and remote control ... Weyland 2001-08-19 10:56:16 UTC Re: [CAD_CAM_EDM_DRO] Interface options, headless boxen, and remote control ... Larry Edington 2001-08-19 11:56:49 UTC Re: [CAD_CAM_EDM_DRO] Interface options, headless boxen, and remote control ... Bryan-TheBS-Smith 2001-08-19 12:07:35 UTC Re: [CAD_CAM_EDM_DRO] Interface options, headless boxen, and remote control ... Larry Edington 2001-08-19 12:10:36 UTC Re: [CAD_CAM_EDM_DRO] Interface options, headless boxen, and remote control ... Bryan-TheBS-Smith 2001-08-19 12:12:03 UTC Re: [CAD_CAM_EDM_DRO] Interface options, headless boxen, and remote control ... Larry Edington 2001-08-19 12:21:41 UTC Re: [CAD_CAM_EDM_DRO] Interface options, headless boxen, and remote control ... Jon Elson 2001-08-19 14:41:57 UTC Re: [CAD_CAM_EDM_DRO] Interface options, headless boxen, and remote control ... Bryan-TheBS-Smith 2001-08-19 16:53:32 UTC Re: [CAD_CAM_EDM_DRO] Interface options, headless boxen, and remote control ... Bryan-TheBS-Smith 2001-08-19 16:56:14 UTC Re: [CAD_CAM_EDM_DRO] Interface options, headless boxen, and remote control ...