CAD CAM EDM DRO - Yahoo Group Archive

Re: Camtronics

Posted by currinh@O...
on 2001-11-14 21:18:32 UTC
Matt:

I built three Camtronic 5A boards for my mill conversion. I also
purchased the steppers and power supply parts from Camtronics. I am very
pleased with the quality of these and would go this way again.

I've done some soldering and didn't find these difficult to build. The
directions are good. Get a loupe (sick in your eye magnifying glass) if
your eyes are old like mine. I did find a couple of spots in the
directions I had trouble understanding, probably due to my lack of an
electronics background. Dan at Camtronics was excellent giving help when
I asked. Likewise there are many on this list who have built these kits
and will be glad to answer questions if you have them. I would not
hesitate to recommend you go with Camtronics.

It does take a while to build these kits. Its a trade of your time
(Camtronics) against cost with pre-assembled boards. But even with
pre-assembled boards you'll need to install in a box, wire together with
plugs, run wires to stepper. I found this to be a non-trivial amount of
time, but enjoyable.

Is this for a mill? What type of machine are you converting?

Hugh Currin
Klamath Falls, OR

On 15 Nov, pkranger63@... wrote:
> Well after some really helpful advice from this group I have decided
> to give CNC a try. I am considring going the "roll your own" and am
> consdiring going with camtronics stepper motor kit. I am a little
> apprehensive about assembling the unit. Is it difficult? I have
> some soldering experince from back in the R/C car racing days but
> that is the extent of my knowledge. Any alternatives I should look
> into? I have also looked into a Maxnc motion control kit but from
> what I have read so far the 70oz motors the kit comes with would
> probably be a bit on the weak side...still the price seems right :)
> As always thanks for the help.
>
> Matt

Discussion Thread

info.host@b... 2001-07-23 16:52:38 UTC Camtronics pkranger63@y... 2001-11-14 18:33:03 UTC Camtronics Tim Goldstein 2001-11-14 18:41:41 UTC RE: [CAD_CAM_EDM_DRO] Camtronics Alan Marconett KM6VV 2001-11-14 18:42:55 UTC Re: [CAD_CAM_EDM_DRO] Camtronics Carol & Jerry Jankura 2001-11-14 20:31:21 UTC RE: [CAD_CAM_EDM_DRO] Camtronics Rich D. 2001-11-14 20:52:20 UTC Re: [CAD_CAM_EDM_DRO] Camtronics currinh@O... 2001-11-14 21:18:32 UTC Re: Camtronics Dan Statman 2001-11-14 22:46:27 UTC Re: [CAD_CAM_EDM_DRO] Camtronics alenz@c... 2001-11-14 23:59:23 UTC Re: Camtronics Carol & Jerry Jankura 2001-11-15 05:24:59 UTC RE: [CAD_CAM_EDM_DRO] Re: Camtronics Tim 2001-11-15 08:36:04 UTC RE: [CAD_CAM_EDM_DRO] Re: Camtronics wayne_j_hill@y... 2001-11-15 08:40:05 UTC Re: Camtronics dlantz@a... 2001-11-15 08:41:59 UTC RE: [CAD_CAM_EDM_DRO] Re: Camtronics Tim 2001-11-15 08:57:05 UTC RE: [CAD_CAM_EDM_DRO] Re: Camtronics currinh@O... 2001-11-15 11:40:45 UTC Re: Camtronics peter smith 2001-11-15 14:33:55 UTC Re: [CAD_CAM_EDM_DRO] Camtronics tauseef 2001-11-15 22:04:20 UTC Re: Camtronics