CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: shielding for steppers

Posted by Steve Smith
on 2001-11-23 20:26:44 UTC
Wouldn't it be a lot easier to replace the cable with a shielded one?

Steve Smith

wanliker@... wrote:

> In a message dated 11/23/2001 3:10:28 AM Mountain Standard Time,
> ccq@... writes:
>
> > There isn't anything that can't be fixed, given an adequate suply of duct
> > tape!
> >
>
> Alternative to duct tape is go to a junk yard, and look for the round split
> plastic covering that is found around the engine and tail light wiring, I
> got a 5 gallon pale full for $3.00. Several diameters available, look for
> the longer ones.
> bill
>
> [Non-text portions of this message have been removed]
>
> Addresses:
> FAQ: http://www.ktmarketing.com/faq.html
> FILES: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/files/
>
> Post messages: CAD_CAM_EDM_DRO@yahoogroups.com
> Subscribe: CAD_CAM_EDM_DRO-subscribe@yahoogroups.com
> Unsubscribe: CAD_CAM_EDM_DRO-unsubscribe@yahoogroups.com
> List owner: CAD_CAM_EDM_DRO-owner@yahoogroups.com, wanliker@...
> Moderator: jmelson@... timg@... [Moderator]
> URL to this page: http://groups.yahoo.com/group/CAD_CAM_EDM_DRO
> bill,
> List Manager
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/

Discussion Thread

cncnut@s... 2001-11-21 19:21:59 UTC shielding for steppers JanRwl@A... 2001-11-21 21:38:30 UTC Re: [CAD_CAM_EDM_DRO] shielding for steppers JanRwl@A... 2001-11-21 21:39:53 UTC Re: [CAD_CAM_EDM_DRO] shielding for steppers Jon Elson 2001-11-21 22:10:35 UTC Re: [CAD_CAM_EDM_DRO] shielding for steppers cncnut@s... 2001-11-22 10:12:30 UTC Re: shielding for steppers Jon Elson 2001-11-22 13:47:18 UTC Re: [CAD_CAM_EDM_DRO] Re: shielding for steppers JanRwl@A... 2001-11-22 14:44:25 UTC Re: [CAD_CAM_EDM_DRO] Re: shielding for steppers mariss92705@y... 2001-11-22 20:17:46 UTC Re: shielding for steppers Bill Vance 2001-11-23 02:10:12 UTC Re: [CAD_CAM_EDM_DRO] Re: shielding for steppers wanliker@a... 2001-11-23 05:30:35 UTC Re: [CAD_CAM_EDM_DRO] Re: shielding for steppers frenner@c... 2001-11-23 07:22:05 UTC Re: shielding for steppers cncnut@s... 2001-11-23 09:00:31 UTC Re: shielding for steppers mariss92705@y... 2001-11-23 09:25:09 UTC Re: shielding for steppers Carol & Jerry Jankura 2001-11-23 13:13:24 UTC RE: [CAD_CAM_EDM_DRO] Re: shielding for steppers Alan Marconett KM6VV 2001-11-23 14:01:27 UTC Re: shielding for steppers JanRwl@A... 2001-11-23 14:42:44 UTC Re: [CAD_CAM_EDM_DRO] Re: shielding for steppers mariss92705@y... 2001-11-23 15:41:19 UTC Re: shielding for steppers shymu@b... 2001-11-23 19:38:44 UTC Re: shielding for steppers Steve Smith 2001-11-23 20:26:44 UTC Re: [CAD_CAM_EDM_DRO] Re: shielding for steppers Bill Vance 2001-11-23 22:22:55 UTC Re: [CAD_CAM_EDM_DRO] Re: shielding for steppers cncnut@s... 2001-11-24 02:25:40 UTC Re: shielding for steppers Bob Campbell 2001-11-24 07:18:01 UTC Re: [CAD_CAM_EDM_DRO] Re: shielding for steppers mariss92705@y... 2001-11-24 11:00:28 UTC Re: shielding for steppers Alan Marconett KM6VV 2001-11-24 11:52:15 UTC Re: shielding for steppers JanRwl@A... 2001-11-24 13:53:28 UTC Re: [CAD_CAM_EDM_DRO] Re: shielding for steppers JanRwl@A... 2001-11-24 14:29:58 UTC Re: [CAD_CAM_EDM_DRO] Re: shielding for steppers Paul 2001-11-24 17:20:11 UTC Re: [CAD_CAM_EDM_DRO] Re: shielding for steppers Steve Smith 2001-11-24 17:36:18 UTC Re: [CAD_CAM_EDM_DRO] Re: shielding for steppers