CAD CAM EDM DRO - Yahoo Group Archive

Re: rotary hand encoder wheels with detent

on 2002-02-14 16:07:12 UTC
It doesn't

I am not too certain that using a mouse would work very
well. I just counted the number of serrations that you
get on a mouse and it is 36; based on previous
conversations on this group, that cannot be increased.
What we really want, however, is a something that
divides 100 cleanly..... If we were to use a 1.8 degree
motor to give us the "tactile" feel, that would give us
200 "clicks" per revolution, which we could engrave on
the dial. When turning the dial quickly, we could
programatically set the travel on the machine to go
1.000, 0.100 or 0.010 (three illuminated buttons);
likewise, if you moved one 'click' to 'edge' the table
over, you'd move 0.0005. If we had a hypothetical 400
resolution encoder attached to this setup that was
perfectly aligned with the motor 'clicks', you would get
2 phase changes per click... very easy to deal with.
Similar logic cold work for an 800 line, 200 line or
even 50 line setup (the latter probably using
pulley/gear multiplication). Anyhow, a 36 line one
doesn't seem to work very well here. We want to have
each 'click' move the same amount.

Or.... I am missing something! Sure, I guess you could
multiply it up pretty far, but it still seems like a
less than ideal setup. Too bad... I liked the idea too.

--Alan

<<<<Original Post>>>>
Message: 11
Date: Thu, 14 Feb 2002 19:28:02 -0000
From: "Ian W. Wright" <Ian@...>
Subject: Re: Re: rotary hand encoder wheels with detent

Perhaps, at last, this is a use for the encoder wheel
out of a mouse!!! ;o)
Hand wheel with clicks, and a rubber band drive from the
hand wheel shaft to
the encoder spindle to gear it up in a suitable
ratio.....

Best wishes,
Ian
--

Discussion Thread

Doug Fortune 2002-02-13 21:17:30 UTC rotary hand encoder wheels with detent Brian Pitt 2002-02-13 21:37:28 UTC Re: [CAD_CAM_EDM_DRO] rotary hand encoder wheels with detent Alan Marconett KM6VV 2002-02-13 21:56:23 UTC Re: [CAD_CAM_EDM_DRO] rotary hand encoder wheels with detent ballendo 2002-02-14 04:03:40 UTC Re: rotary hand encoder wheels with detent dlantz@a... 2002-02-14 05:40:26 UTC RE: [CAD_CAM_EDM_DRO] rotary hand encoder wheels with detent Alan Brumley 2002-02-14 06:08:27 UTC Stepper Motor Source Garry & Maxine Foster 2002-02-14 06:39:20 UTC Re: [CAD_CAM_EDM_DRO] rotary hand encoder wheels with detent Mr. sausage 2002-02-14 07:18:21 UTC Re: [CAD_CAM_EDM_DRO] rotary hand encoder wheels with detent Doug Fortune 2002-02-14 07:55:23 UTC RE: [CAD_CAM_EDM_DRO] rotary hand encoder wheels with detent rcstickman 2002-02-14 07:57:12 UTC Re: Stepper Motor Source Doug Fortune 2002-02-14 08:00:32 UTC Re: [CAD_CAM_EDM_DRO] rotary hand encoder wheels with detent Scot Rogers 2002-02-14 08:26:26 UTC RE: [CAD_CAM_EDM_DRO] rotary hand encoder wheels with detent dlantz@a... 2002-02-14 09:16:20 UTC RE: [CAD_CAM_EDM_DRO] rotary hand encoder wheels with detent Mark Ehle 2002-02-14 09:28:36 UTC Re: [CAD_CAM_EDM_DRO] Stepper Motor Source Jon Elson 2002-02-14 10:16:57 UTC Re: [CAD_CAM_EDM_DRO] Stepper Motor Source mariss92705 2002-02-14 10:33:13 UTC Re: rotary hand encoder wheels with detent Alan Marconett KM6VV 2002-02-14 10:44:36 UTC Re: [CAD_CAM_EDM_DRO] Re: rotary hand encoder wheels with detent dlantz@a... 2002-02-14 11:02:45 UTC RE: [CAD_CAM_EDM_DRO] Re: rotary hand encoder wheels with detent Ian W. Wright 2002-02-14 11:27:34 UTC Re: [CAD_CAM_EDM_DRO] Re: rotary hand encoder wheels with detent Alan Marconett KM6VV 2002-02-14 11:57:14 UTC Re: [CAD_CAM_EDM_DRO] rotary hand encoder wheels with detent Alan Marconett KM6VV 2002-02-14 12:11:20 UTC Re: [CAD_CAM_EDM_DRO] Stepper Motor Source dlantz@a... 2002-02-14 12:15:56 UTC RE: [CAD_CAM_EDM_DRO] rotary hand encoder wheels with detent Alan Marconett KM6VV 2002-02-14 12:23:39 UTC Re: [CAD_CAM_EDM_DRO] rotary hand encoder wheels with detent Alan Marconett KM6VV 2002-02-14 12:26:41 UTC Re: [CAD_CAM_EDM_DRO] rotary hand encoder wheels with detent Alan Marconett KM6VV 2002-02-14 12:54:17 UTC Re: [CAD_CAM_EDM_DRO] rotary hand encoder wheels with detent Carol & Jerry Jankura 2002-02-14 13:52:00 UTC RE: [CAD_CAM_EDM_DRO] Stepper Motor Source flyspeck1@a... 2002-02-14 16:07:12 UTC Re: rotary hand encoder wheels with detent JanRwl@A... 2002-02-14 18:46:36 UTC Re: [CAD_CAM_EDM_DRO] Stepper Motor Source Doug Fortune 2002-02-14 19:19:13 UTC Re: rotary hand encoder wheels with detent Mr. sausage 2002-02-14 21:03:49 UTC Re: [CAD_CAM_EDM_DRO] Stepper Motor Source Jon Elson 2002-02-14 22:35:02 UTC Re: [CAD_CAM_EDM_DRO] Stepper Motor Source Ian W. Wright 2002-02-15 02:59:37 UTC Re: [CAD_CAM_EDM_DRO] Re: rotary hand encoder wheels with detent aspaguy 2002-02-15 12:51:26 UTC Re: Stepper Motor Source tedinoue 2002-02-16 03:55:19 UTC Re: rotary hand encoder wheels with detent imserv1 2002-02-16 09:00:47 UTC Re: rotary hand encoder wheels with detent audiomaker2000 2002-02-16 09:13:19 UTC Re: rotary hand encoder wheels with detent audiomaker2000 2002-02-16 09:29:09 UTC Re: rotary hand encoder wheels with detent Alan Marconett KM6VV 2002-02-16 14:22:05 UTC Re: rotary hand encoder wheels with detent wanliker@a... 2002-02-16 17:18:28 UTC Re: [CAD_CAM_EDM_DRO] Re: rotary hand encoder wheels with detent imserv1 2002-02-16 22:20:11 UTC Re: rotary hand encoder wheels with detent Alan Marconett KM6VV 2002-02-17 12:10:29 UTC Re: rotary hand encoder wheels with detent audiomaker2000 2002-02-17 12:30:53 UTC Re: rotary hand encoder wheels with detent imserv1 2002-02-17 13:42:18 UTC Re: rotary hand encoder wheels with detent wanliker@a... 2002-02-17 15:20:14 UTC Re: [CAD_CAM_EDM_DRO] Re: rotary hand encoder wheels with detent ballendo 2002-02-17 23:20:53 UTC ball plungers was Re: rotary hand encoder wheels with detent Alan Marconett KM6VV 2002-02-18 10:35:51 UTC Re: rotary hand encoder wheels with detent Mike Snodgrass 2002-02-18 11:19:07 UTC Re: [CAD_CAM_EDM_DRO] Re: rotary hand encoder wheels with detent Alan Marconett KM6VV 2002-02-18 11:20:26 UTC Re: rotary hand encoder wheels with detent Alan Brumley 2002-02-18 11:37:08 UTC RE: [CAD_CAM_EDM_DRO] Stepper Motor Source Alan Marconett KM6VV 2002-02-18 11:45:39 UTC Re: rotary hand encoder wheels with detent Carlos Guillermo 2002-02-18 11:51:34 UTC Re: rotary hand encoder wheels with detent Angelos 2002-02-18 12:27:17 UTC Re: [CAD_CAM_EDM_DRO] Re: rotary hand encoder wheels with detent Brian Pitt 2002-02-18 13:03:35 UTC Re: [CAD_CAM_EDM_DRO] Re: rotary hand encoder wheels with detent Smoke 2002-02-18 14:05:15 UTC Re: [CAD_CAM_EDM_DRO] Re: rotary hand encoder wheels with detent Alan Marconett KM6VV 2002-02-18 14:10:09 UTC Re: rotary hand encoder wheels with detent imserv1 2002-02-18 14:34:16 UTC Re: rotary hand encoder wheels with detent Carol & Jerry Jankura 2002-02-18 17:46:01 UTC RE: [CAD_CAM_EDM_DRO] Re: rotary hand encoder wheels with detent Alan Marconett KM6VV 2002-02-18 17:46:55 UTC Re: rotary hand encoder wheels with detent ballendo 2002-02-19 02:08:27 UTC Feedrate overide was Re: rotary hand encoder wheels with detent ballendo 2002-02-19 04:05:06 UTC keyboard typematic and old dos stuff was Re: rotary hand encoder wheels... Alan Marconett KM6VV 2002-02-19 10:54:07 UTC Re: rotary hand encoder wheels with detent jeffdavis516 2002-02-19 11:23:47 UTC Feedrate overide was Re: rotary hand encoder wheels with detent Alan Marconett KM6VV 2002-02-19 11:31:56 UTC Re: [CAD_CAM_EDM_DRO] Feedrate overide was Re: rotary hand encoder wheels with detent