CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] Re: Linear rail & ball screw size suggestions

Posted by Les Watts
on 2002-04-11 10:08:26 UTC
> Hiwin ball screws are also dropping in cost... a 1" diam ballscrew
> with .200 lead, preloaded flanged ballnut, 49" OAL, (need the ends to
> be machined) is $185... this is a nice screw!
>
> If I was building a machine, I would want it stiff, I wouldn't want
> the tool moving around on me... the bearings and the screw are the
> heart of stiffness. I know, I know... it's only a light load, and
> little forces

I have been using the HIWIN screws mike mentioned for a few
years...in fact they are the ones pictured on the engineering
portion of my website.

They generally map out to better than 0.003" max absolute
error over the entire length. The oversize ball preload is
very very stiff and the drag preload torque is low.

As far as robust machine components, even a lightly loaded
machine will have huge forces during a collision or crash.
To me the linear rails just blow away round shafting or
grooved wheel trolleys - and they are so easy to use.
You just need a good flat surface to bolt them to. I usually
also dowel pin the master rail.

Les


Leslie Watts
L M Watts Furniture
Tiger, Georgia USA
http://www.rabun.net/~leswatts/wattsfurniturewp.html
engineering page:
http://www.rabun.net/~leswatts/shop.html
----- Original Message -----

Discussion Thread

J.Critchfield 2002-04-09 18:38:15 UTC Linear rail & ball screw size suggestions dave_ace_me 2002-04-09 20:34:36 UTC Re: Linear rail & ball screw size suggestions Mark Taft 2002-04-10 00:42:54 UTC RE: [CAD_CAM_EDM_DRO] Linear rail & ball screw size suggestions CL 2002-04-10 05:57:12 UTC Re: [CAD_CAM_EDM_DRO] Linear rail & ball screw size suggestions dave_ace_me 2002-04-10 16:25:40 UTC Re: Linear rail & ball screw size suggestions J.Critchfield 2002-04-10 16:56:51 UTC Re: [CAD_CAM_EDM_DRO] Linear rail & ball screw size suggestions dave_ace_me 2002-04-10 17:40:11 UTC Re: Linear rail & ball screw size suggestions William Scalione 2002-04-10 17:57:27 UTC Re: [CAD_CAM_EDM_DRO] Linear rail & ball screw size suggestions J.Critchfield 2002-04-10 17:57:42 UTC Re: [CAD_CAM_EDM_DRO] Re: Linear rail & ball screw size suggestions dave_ace_me 2002-04-10 19:06:18 UTC Re: Linear rail & ball screw size suggestions Chris L 2002-04-10 19:46:13 UTC Re: [CAD_CAM_EDM_DRO] Linear rail & ball screw size suggestions J.Critchfield 2002-04-10 19:46:47 UTC Re: [CAD_CAM_EDM_DRO] Re: Linear rail & ball screw size suggestions JanRwl@A... 2002-04-10 20:57:11 UTC Re: [CAD_CAM_EDM_DRO] Re: Linear rail & ball screw size suggestions Bill Vance 2002-04-10 21:17:55 UTC Re: [CAD_CAM_EDM_DRO] Re: Linear rail & ball screw size suggestions JanRwl@A... 2002-04-10 21:21:43 UTC Re: [CAD_CAM_EDM_DRO] Linear rail & ball screw size suggestions JanRwl@A... 2002-04-10 21:45:59 UTC Re: [CAD_CAM_EDM_DRO] Re: Linear rail & ball screw size suggestions J.Critchfield 2002-04-10 21:54:10 UTC Re: [CAD_CAM_EDM_DRO] Linear rail & ball screw size suggestions J.Critchfield 2002-04-10 22:55:49 UTC Re: [CAD_CAM_EDM_DRO] Re: Linear rail & ball screw size suggestions dave_ace_me 2002-04-11 04:52:35 UTC trim router( wasRe: Linear rail & ball screw size suggestions dumbdrive 2002-04-11 05:55:59 UTC Re: Linear rail & ball screw size suggestions CL 2002-04-11 06:03:03 UTC Re: [CAD_CAM_EDM_DRO] Re: Linear rail & ball screw size suggestions dave_ace_me 2002-04-11 06:23:45 UTC Re: Linear rail & ball screw size suggestions dave_ace_me 2002-04-11 06:35:40 UTC dust and rails ( was Re: Linear rail & ball screw size suggestions J.Critchfield 2002-04-11 06:51:32 UTC Re: [CAD_CAM_EDM_DRO] dust and rails ( was Re: Linear rail & ball screw size suggestions dave_ace_me 2002-04-11 08:42:29 UTC dust and rails ( was Re: Linear rail & ball screw size suggestions Les Watts 2002-04-11 10:08:26 UTC Re: [CAD_CAM_EDM_DRO] Re: Linear rail & ball screw size suggestions dumbdrive 2002-04-11 10:58:00 UTC Re: Linear rail & ball screw size suggestions Tim Goldstein 2002-04-11 11:38:12 UTC Re: [CAD_CAM_EDM_DRO] Re: Linear rail & ball screw size suggestions dave_ace_me 2002-04-11 12:50:50 UTC OT self promotion ( was Re: Linear rail & ball screw size suggestions Scott Hendershot 2002-04-11 17:07:46 UTC Re: [CAD_CAM_EDM_DRO] trim router( wasRe: Linear rail & ball screw size suggestions dave_ace_me 2002-04-11 19:23:12 UTC all-thread lead screw( was Re: Linear rail & ball screw size suggestions Chris L 2002-04-11 22:04:12 UTC Re: [CAD_CAM_EDM_DRO] trim router( wasRe: Linear rail & ball screw size suggestions Doug Fortune 2002-04-11 22:06:58 UTC Re: [CAD_CAM_EDM_DRO] Linear rail & ball screw size suggestions batwings@i... 2002-04-12 04:38:49 UTC Re: [CAD_CAM_EDM_DRO] Linear rail & ball screw size suggestions dave_ace_me 2002-04-12 05:23:49 UTC Re: Linear rail & ball screw size suggestions JanRwl@A... 2002-04-12 19:18:03 UTC Re: [CAD_CAM_EDM_DRO] Linear rail & ball screw size suggestions JanRwl@A... 2002-04-12 19:18:22 UTC Re: [CAD_CAM_EDM_DRO] Re: Linear rail & ball screw size suggestions William Scalione 2002-04-12 20:44:45 UTC Re: [CAD_CAM_EDM_DRO] Linear rail & ball screw size suggestions ballendo 2002-04-14 04:49:53 UTC Re: Linear rail & ball screw size suggestions ballendo 2002-04-14 05:03:38 UTC Re: Linear rail & ball screw size suggestions dave_ace_me 2002-04-14 07:25:26 UTC Re: Linear rail & ball screw size suggestions J.Critchfield 2002-04-14 09:19:35 UTC Re: [CAD_CAM_EDM_DRO] Re: Linear rail & ball screw size suggestions