CAD CAM EDM DRO - Yahoo Group Archive

Re: [CAD_CAM_EDM_DRO] water level ( was Re: Aligning Rails (or ways) on CNC router

Posted by Jon Elson
on 2002-08-16 10:09:37 UTC
turbulatordude wrote:

> If you want a more accurate water level, get a glass tube from a
> hobby store, probably a foot length is common. 3/8 would be about a
> good size. don't go smaller than 1/4, and 1/2 is not adding anything.

Well, this may be sufficient for a wood router. it certainly is no
substitute for a master precision level, which will easily detect
the thickness of a single hair over a lever arm of a foot or more.
Without exotic attachments, I doubt you can do much better than
1/16th of an inch. If you are just concerned with getting the ends of
the rails at the same height, that may be almost good enough.
But, if you want to look for a hump or sag in the middle of the
rails, the water level just isn't sensitive enough.

Jon

Discussion Thread

bob_santa 2002-08-15 09:11:45 UTC Aligning Rails (or ways) on CNC router Bill Vance 2002-08-15 10:32:47 UTC Re: [CAD_CAM_EDM_DRO] Aligning Rails (or ways) on CNC router Jon Elson 2002-08-15 10:55:11 UTC Re: [CAD_CAM_EDM_DRO] Aligning Rails (or ways) on CNC router castinggrain 2002-08-15 20:33:57 UTC Re: [CAD_CAM_EDM_DRO] Aligning Rails (or ways) on CNC router Bill Vance 2002-08-15 21:43:40 UTC Re: [CAD_CAM_EDM_DRO] Aligning Rails (or ways) on CNC router turbulatordude 2002-08-16 04:01:42 UTC water level ( was Re: Aligning Rails (or ways) on CNC router Jon Elson 2002-08-16 10:09:37 UTC Re: [CAD_CAM_EDM_DRO] water level ( was Re: Aligning Rails (or ways) on CNC router Randy Gordon-Gilmore 2002-08-16 11:18:57 UTC Re: [CAD_CAM_EDM_DRO] water level Randy Gordon-Gilmore 2002-08-16 11:35:01 UTC Another question about leveling/squaring mayfieldtm 2002-08-16 11:37:12 UTC master precision levels Doug Harrison 2002-08-16 12:55:55 UTC Re: [CAD_CAM_EDM_DRO] master precision levels turbulatordude 2002-08-16 15:05:25 UTC water level ( was Re: Aligning Rails (or ways) on CNC router bob_santa 2002-08-16 17:35:24 UTC Re: Aligning Rails (or ways) on CNC router Jon Elson 2002-08-16 20:53:25 UTC Re: [CAD_CAM_EDM_DRO] master precision levels Jon Elson 2002-08-16 21:24:03 UTC Re: [CAD_CAM_EDM_DRO] water level ( was Re: Aligning Rails (or ways) on CNC router turbulatordude 2002-08-17 06:03:32 UTC water level ( was Re: Aligning Rails (or ways) on CNC router Carlos Guillermo 2002-08-27 11:04:43 UTC RE: [CAD_CAM_EDM_DRO] master precision levels Randy Gordon-Gilmore 2002-08-27 17:00:48 UTC Demise of free Intellicad Randy Gordon-Gilmore 2002-08-27 17:33:51 UTC Re: [CAD_CAM_EDM_DRO] Demise of free Intellicad Doug Harrison 2002-08-27 17:34:28 UTC RE: [CAD_CAM_EDM_DRO] master precision levels LEW BEST 2002-08-27 18:46:44 UTC RE: [CAD_CAM_EDM_DRO] master precision levels studleylee 2002-08-27 20:19:41 UTC Re: master precision levels Jeff Hamilton 2002-08-27 20:50:28 UTC Cutting Glass scales Dave Lantz 2002-08-28 05:21:30 UTC RE: [CAD_CAM_EDM_DRO] Demise of free Intellicad Kos 2002-08-29 02:36:05 UTC Re: [CAD_CAM_EDM_DRO] Demise of free Intellicad Randy Gordon-Gilmore 2002-08-29 14:58:53 UTC BDI question and Knoppix plug wanliker@a... 2002-08-29 15:22:19 UTC Re: [CAD_CAM_EDM_DRO] BDI question and Knoppix plug Randy Gordon-Gilmore 2002-08-29 15:33:03 UTC Re: BDI question and Knoppix plug William Scalione 2002-08-29 22:26:45 UTC Re: [CAD_CAM_EDM_DRO] BDI question and Knoppix plug Ian W. Wright 2002-08-30 01:22:07 UTC Re: [CAD_CAM_EDM_DRO] Re: BDI question and Knoppix plug Ray Henry 2002-08-30 09:07:13 UTC Re: Re: Re: BDI question and Knoppix plug Ian W. Wright 2002-08-30 10:43:51 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: Re: BDI question and Knoppix plug Bill Vance 2002-08-30 11:55:49 UTC Re: [CAD_CAM_EDM_DRO] Re: BDI question and Knoppix plug j.guenther 2002-08-30 12:05:25 UTC RE: [CAD_CAM_EDM_DRO] Re: BDI question and Knoppix plug jmkasunich 2002-08-30 14:21:53 UTC EMC / BDI / Linux / RTLinux / RTAI confusion Bill Vance 2002-08-30 14:44:45 UTC Re: [CAD_CAM_EDM_DRO] Re: BDI question and Knoppix plug Randy Gordon-Gilmore 2002-08-30 22:48:43 UTC Re: [CAD_CAM_EDM_DRO] BDI question and Knoppix plug Jon Elson 2002-08-30 23:03:36 UTC Re: [CAD_CAM_EDM_DRO] EMC / BDI / Linux / RTLinux / RTAI confusion Randy Gordon-Gilmore 2002-08-31 02:15:08 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: Re: BDI question and Knoppix plug funcadem 2003-07-22 02:43:07 UTC Re: Re: BDI question and Knoppix plug Paul 2003-07-22 10:05:25 UTC Re: [CAD_CAM_EDM_DRO] Re: Re: BDI question and Knoppix plug funcadem 2003-07-22 13:13:53 UTC Re: BDI question and Knoppix plug funcadem 2003-07-22 13:20:30 UTC Re: BDI question and Knoppix plug Paul 2003-07-22 13:36:57 UTC Re: [CAD_CAM_EDM_DRO] Re: BDI question and Knoppix plug